2015 Chrysler 200 S on 2040-cars

Auto blog

78k Chrysler 200 sedans recalled for stalling

Chrysler has been at the top of our list of recalls lately, and is showing little sign of dropping down. The latest campaign announced from Auburn Hills affects nearly 80,000 units over a problem that could see the vehicle suddenly stall or shift into neutral unexpectedly. According to the automaker's statement below, the issue primarily affects the 2015 Chrysler 200. However it indicates that unspecified "additional vehicles are also included in the campaign." Of the 77,834 units affected by the recall, the vast majority – nearly 70k – are in the United States. Another 7,115 are located in Canada, 848 in Mexico, and another 19 outside of North America. The problem stems from some electrical connectors that may have been damaged by the supplier during post-production validation tests. FCA stresses, however, that it is "unaware of any related injuries or accidents" resulting from this issue, and that the glitch may or may not be "accompanied by a dashboard warning-light illumination." Airbag function is reportedly unaffected. Related Video: Statement: Electrical Connectors August 14, 2015 , Auburn Hills, Mich. - FCA US LLC is conducting a voluntary safety recall to correct a condition in an estimated 77,834 U.S.-market sedans that may lead to engine stall or gearshift to neutral. The Company is unaware of any related injuries or accidents. The condition, which may be accompanied by a dashboard warning-light illumination, does not affect air-bag function. An investigation by FCA US revealed some electrical connectors were damaged when the supplier conducted post-production validation tests. Affected are certain 2015 Chrysler 200 midsize sedans. Additional vehicles also are included in campaign. Of these, approximately 7,115 are in Canada; 848 are in Mexico; and 19 are outside the NAFTA region Affected customers will be advised when they may schedule service, which will be performed free of charge. Customers with questions or concerns may call the FCA US Customer Care Center at 1-800-853-1403.

Mopar celebrates 50 years of the 426 Hemi

Think of Chrysler performance and the names Mopar and Hemi are bound to come to mind. Chrysler and its Mopar performance parts division first introduced the original Hemi (so named for its hemispherical combustion chambers) back in 1951, celebrating its 60th anniversary in 2011. But it was thirteen years later - 50 years ago - that the Pentastar automaker rolled out the most iconic Hemi of them all: the Gen II 426.
The massive 7.0-liter V8 engine instantly became a muscle car icon and went on to become a favorite of racecar constructors. Two competition versions of the Gen II 426 Hemi were made: one for the track and one for the drag strip, and both went on to illustrious strings of victories. The race engine first debuted at the 1964 Daytona 500 where it powered Richard Petty's Plymouth to the checkered flag and on to the NASCAR championship.
Meanwhile on the drag strip, the Gen II 426 Race Hemi propelled Don Garlits past 200 miles per hour and down the quarter-mile in 7.78 seconds. Changes in NASCAR regulations meant that Chrysler devoted the engine to NHRA drag racing, and to this day the Gen II 426 Race Hemi is still used in Funny Car and Top Fuel dragsters.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.