2014 Chevrolet Traverse 1lt on 2040-cars

Auto blog

Ringbrothers drops more hints about its wild SEMA creations

Ringbrothers isn't finished teasing its SEMA creations. First we got a sliver of rear quarter on a 1969 Chevrolet Camaro that revealed a bundle of carbon fiber and SEMA-obligatory deep-dish wheels. The Wisconsin tuner's now announced its litter of cars headed to the show and a few specs, along with two shadowy drawings. The Camaro, christened with the name Valkyrja and a two-tone paint job, gets stretched in two directions with severe fender flares to widen the body and an extended wheelbase. We're not sure what's happening with the Camaro's snout in the drawing, but under that bulging hood we'll find a 416-cubic-inch LS V8 from Wegner Motorsports. Wegner built the 416-cu-in supercharged LS3 V8 that powered Ringbrothers' 1,000-hp G-Code Camaro in 2016.  The second member of the gang is a 1969 Ford Mustang Mach 1 dubbed Unkl. The exterior begs for attention with a deep blue sea paint job, deep front chin spoiler, bulging hood, yellow brake calipers, and what looks like a racing number inside a roundel on the doors. Unkl gets its motivation from a 520-cu-in Boss V8 built by Kaase Racing Engines, rumored to throw about 800 hp.    Finally, Ringbrothers is bringing its Cadillac Madam V for another Las Vegas go-round after giving the custom coupe some updates. The Madam V is a 1948 Cadillac Series 62 fastback coupe body placed atop an ATS-V chassis, first shown in 2016. The firm didn't elaborate on the changes, so all we can expect for now are the coupe's postwar good looks mixed with new-millennium engineering, and a 3.6-liter twin-turbo V6 with 464 hp under that exceptionally long hood.    For any in attendance at the show, the Valkyrja Camaro debuts at the BASF booth on Tuesday, Nov. 5, 2019 at 9:30 a.m., the Unkl Mustang gets revealed a couple hours later at the Flowmaster/Holley booth, and the Madam V Cadillac will be on display throughout the show at the Ringbrothers booth.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

Expect greater differentiation in GM's next-generation SUVs

General Motors says its next-generation Chevrolet Tahoe, Suburban, GMC Yukon and Cadillac Escalade models will offer shoppers improved interior differentiation. Car and Driver recently caught up with Chris Hilts, GM's creative manager of interior design, who said that the cabins will all feature unique instrument panels, consoles, center stacks and switchgear moving forward. Apparently GM is now aware that consumers may be bothered by the fact that today's $85,000 Escalade has effectively the same cabin as a $45,000 Tahoe. Hilts says SUV buyers want more refinement than their pickup purchasing counterparts - and those same buyers also want their SUVs to have more exterior differentiation between the company's Silverado and Sierra pickup lines. Shocking.
That all sounds good to us, but we've heard this song and dance before. GM made big waves about how different the new-for-2013 Silverado and Sierra would look from each other, but judging by what we've seen so far, GM's stylists are painting in shades rather than with the full spectrum. For more on the what to expect out of GM's new SUVs, click on the C/D link below.