2014 Chevrolet Traverse 1lt on 2040-cars

Auto blog

2016 Chevrolet Camaro powers up, slims down

Don't be fooled by its familiar appearance, the 2016 Chevrolet Camaro is vastly different than its iconic predecessors. It has a new chassis, a fresh engine lineup, and is loaded with clever technologies that promise to invigorate and improve the sixth generation of Chevy's legendary sports car. It was revealed Saturday before a crowd of enthusiastic Camaro revelers on Belle Isle in Detroit. Redesigning the sports coupe was a heady task, especially as its archrivals, the Ford Mustang and Dodge Challenger, drive better and are more powerful than ever. But the new Camaro is aiming to be the best combination of handling and raw performance, with quick acceleration and competitive fuel economy. "Redesigning the Camaro is thrilling and challenging all at once, but the secret is to offer something more," Mark Reuss, General Motors executive vice president of product development, said in a statement. It all began with a weight-loss plan. The new Camaro shed more than 200 pounds compared with the outgoing car, with 133 pounds coming from a lighter body-in-white. Then engineers culled weight nearly everywhere, using aluminum for the instrumental panel frame and some suspension components to trim as much fat as possible. The slimmer body rests on new bones. The Camaro's rear-wheel-drive platform is lighter and stiffer in a bid to improve handling. It's a modified version of the underpinnings used by the Cadillac ATS, though about 70 percent of the architecture is unique to the Camaro. Chevy said structural rigidity is improved by 28 percent. As you'll see, healthy doses of Cadillac and Corvette technologies have been used to bolster the Camaro's drive character and performance. The new car is also expected to handle better thanks to a slightly smaller footprint. It is about two inches shorter in length, with most of that due to the more compact wheelbase. It's also an inch shorter in height and an inch slimmer in width. So yes, the Camaro will be leaner, but it will still be plenty mean. The Camaro SS tops the range (for now) with the Corvette's 6.2-liter V8 pushing put 455 horsepower and 455 pound-feet of torque. Known as the LT1, is has a cast aluminum block and cast aluminum cylinder heads, and it's fortified with direct injection, variable valve timing, and cylinder deactivation. About 20 percent of the engine's parts are said to be unique to the Camaro, including the exhaust manifolds.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Chevy Bolt 200-mile EV going into production near Detroit

Where there's smoke, there's fire, apparently. The rumors of the Chevy Bolt going into production have been proven correct, with an announcement this morning at the Chicago Auto Show that the 200-mile, all-electric Bolt will be built at the Orion Assembly facility near Detroit. GM didn't say exactly when the Bolt will be built, but GM North America president Alan Batey said in a statement that, "We are moving quickly because of its potential to completely shake up the status quo for electric vehicles." He's not kidding. GM is talking about a $30,000 price tag for an EV that can do twice as many electric miles as any non-Tesla mass-production EV today. Previous hints have the Bolt starting production next year for a market debut in 2017, and with all of the accuracy we've seen from these secret releases up to now, we're going to say this is probably accurate until we hear otherwise. We still have questions about the price tag, but for now we'll try to track down more information here in Chicago. Chevrolet Commits to Bolt EV Production Game-changing, long-range EV to be built at Orion Assembly facility in Michigan CHICAGO – Chevrolet this morning confirmed production of its next-generation pure electric vehicle, based on the Bolt EV concept. It will be built at General Motors' Orion Assembly facility near Detroit. GM North America President Alan Batey made the announcement ahead of the Chicago Auto Show. The Bolt EV concept was introduced last month at the North American International Auto Show in Detroit. "The message from consumers about the Bolt EV concept was clear and unequivocal: Build it," said Batey. "We are moving quickly because of its potential to completely shake up the status quo for electric vehicles." Leveraging the industry-leading battery technology found in the Chevrolet Volt and Spark EV, the Bolt EV concept was developed as a game-changing, long-range pure electric for all 50 states, designed to offer more than a GM-estimated 200 miles of range at a target price of around $30,000. The progressively styled concept vehicle features selectable driving modes for preferred driving styles, such as daily commuting, and it was designed to support DC fast charging. "We're proud that Chevrolet has decided to produce the Bolt EV here in Michigan at the Orion Assembly facility," Gov. Rick Snyder said. "Michigan unquestionably remains the global automotive leader.