2006 Chevy Silverado 3500 Diesel Ext Cab,4 Drs, Reese 16k Hitch,dual Rearwheels on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

MotorWeek Retro Review revisits 1984 Corvette

MotorWeek's Retro Reviews are always a great glimpse into the cars of yesteryear. However, the newly uploaded look back at the 1984 Chevrolet Corvette is an absolute treasure trove for any auto history buff. This is a full episode of the show from the '80s, and it's dedicated to all of the details about the newest 'Vette to hit the market at the time. Beyond just the usual drive and an in-depth walk around, one of the major highlights here is a brief look at some on the concepts that eventually resulted in the fourth-generation Corvette of 1984. The C4's shape harkens back to sketches from 1978, and there even shots of early clay models that led the way for the design. MotorWeek also takes a tour through the Bowling Green, KY, factory for a detailed inspection of the entire production process. John Davis repeatedly calls the Corvette "the plastic fantastic" during the episode, and he can't find too much negative to say about being behind the wheel of the then-new coupe. See how it stands up to your own memories in the clip above.

Genovation Cars readies all-electric Corvette prototype

Chevy runs the full spectrum from some of the most environmentally friendly cars to the least. At one end are EVs like the Spark and Volt. At the other, performance models like the Camaro and Corvette. But one American company wants to bridge that divide. That company is Rockville, MD-based Genovation Cars, which reports that it is almost done building its prototype for an all-electric Corvette. Dubbed the Genovation Extreme Electric (or GXE for short), the prototype is based on a previous-generation 2006 Chevy Corvette Z06, but ditches its enormous 7.0-liter V8 for an array of inverters, batteries, and electric motors said to be good for over 700 horsepower and 600 pound-feet of torque. That promises to deliver a 0-60 time of about 3.0 seconds and a top speed in excess of 200 miles per hour. Those are supercar benchmarks for performance if we've ever seen them, and ought to leave even the top-spec Tesla Model S P85D in... well, not a cloud of smoke, but whatever the electric equivalent is, in a non-polluting cloud of that. The GXE is also supposed to be able to travel for 150 miles on a single charge, and handle well while it's at it with 50/50 front-rear weight distribution and a low center of gravity. Sorta like the Power Wheels 'Vette pictured above, then, but bigger and faster. Look for the GXE to debut at the Electric Vehicle Technology Expo this coming September in Michigan, after which Genovation says it will put the GXE to the test on the track to back up its performance claims. Genovation Cars Nearing Completion of High-Performance All-Electric Corvette, the GXE ROCKVILLE, Md.--(BUSINESS WIRE)--Genovation Cars is nearing the completion of a prototype high-performance all-electric Corvette called the Genovation Extreme Electric or GXE. Assembly of the GXE will be completed by the end of July, followed by a three-week testing phase. The GXE is based on a 2006 Z06 Corvette. Several contributors to the GXE effort have helped design and build record-breaking electric vehicles. They include an MIT electrical engineer and a mechanical engineer from Cosworth. "We are using state of the art inverters, batteries and electric motors that will produce in excess of 700-hp and 600 lb-ft of torque," said Genovation CEO Andrew Saul. "We expect the car to achieve 0-60 mph in around three seconds and have a top speed of over 200 mph.