Work Truck C 4x4 Air Conditioning Alarm System Am/fm Anti-lock Brakes Tachometer on 2040-cars

Auto blog

GM extends vehicle production cuts into mid-March due to global chip shortage

DETROIT — General Motors said on Tuesday it was extending production cuts at three North American plants until at least mid-March due to the global semiconductor chip shortage, while vehicles at two other factories would only be partially built. GM, whose shares dipped 1% after the announcement, did not disclose the impact volumes or say which supplier and vehicle parts were affected by the chip shortage. But it said it would focus on keeping production running at plants building its highest-profit vehicles, full-size pickup trucks and SUVs. GM said it intended to make up as much lost production as possible once the shortage chip eased. "Semiconductor supply remains an issue that is facing the entire industry. GM's plan is to leverage every available semiconductor to build and ship our most popular and in-demand products," GM spokesman David Barnas said. GM said it was extending downtime at its U.S. plant in Fairfax, Kansas, its Canadian factory in Ingersoll, Ontario, and its Mexican facility in San Luis Petosi until mid-March when it would reassess the situation, he said. In addition, GM would build but leave incomplete for final assembly vehicles at Wentzville, Missouri, and its Mexican plant at Ramos Arizpe. GM vehicles affected by the idled plants include the Chevrolet Malibu sedan, Cadillac XT4 SUV, Chevy Equinox, and GMC Terrain SUVs. Vehicles to be left incomplete for now included the Chevy Colorado, GMC Canyon pickups and Chevy Blazer SUV. This week, GM had said it was idling the three factories where it has now extended downtime and said it would halve production at a plant in South Korea. The chip shortage has affected many automakers, including Toyota, Volkswagen, Stellantis, Ford, Renault, Subaru, Nissan, Honda and Mazda. Asian chipmakers are rushing to boost production but say the supply gap will take many months to plug. German chipmaker Infineon said the shortage would get worse in the near term. The chip shortage is expected to cut global output in the first quarter by more than 670,000 vehicles and last into the third quarter, IHS Markit said. AutoForecast Solutions estimated total lost production this year could reach 1 million vehicles. Honda and Nissan said on Tuesday they would sell 250,000 fewer cars in total this financial year due.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.