2015 Navigation Leather Mylink Rear Camera V8 Duramax Diesel on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM isn't liable for punitive damages in ignition switch cases

NEW YORK — A federal appeals court said General Motors is not liable for punitive damages over accidents that occurred after its 2009 bankruptcy and involved vehicles it produced earlier, including vehicles with faulty ignition switches. The 2nd U.S. Circuit Court of Appeals in Manhattan said on Tuesday that the automaker did not agree to contractually assume liability for punitive damages as part of its federally-backed Chapter 11 reorganization. GM filed for bankruptcy in June 2009, and its best assets were transferred to a new Detroit-based company with the same name. The other assets and many liabilities stayed with "Old GM," which is also known as Motors Liquidation Co. Tuesday's 3-0 decision may help GM reduce its ultimate exposure in nationwide litigation over defective ignition switches in several Chevrolet, Pontiac and Saturn models. It is also a defeat for drivers involved in post-bankruptcy accidents, including those who collided with older GM vehicles driven by others, as well as their law firms. The ignition switch defect could cause engine stalls and keep airbags from deploying, and has been linked to 124 deaths. A lawyer for the drivers and their law firms did not immediately respond to requests for comment. GM had no comment. Circuit Judge Dennis Jacobs said GM's agreement to acquire assets "free and clear" of most liabilities excused it from punitive damages claims for Old GM's conduct. He also noted that the judge who oversaw the bankruptcy concluded that the new company could not be liable for claims that the "deeply insolvent" Old GM would never have paid. The decision upheld a May 2018 ruling by U.S. District Judge Jesse Furman in Manhattan, who oversees the ignition switch litigation. Drivers have sought a variety of damages in that litigation, including for declining resale values. GM has recalled more than 2.6 million vehicles since 2014 over ignition switch problems. It has also paid more than $2.6 billion in related penalties and settlements, including $900 million to settle a U.S. Department of Justice criminal case. The case is In re: Motors Liquidation Co, 2nd U.S. Circuit Court of Appeals, No. 18-1940. Government/Legal Chevrolet Pontiac Saturn Safety gm ignition switch

Chevy Colorado, GMC Canyon get updated tachometers due to graphical error

After James Bearing bought a Chevrolet Colorado, he noticed a discrepancy between the truck's spec sheet and the truck's tachometer: Chevrolet said 3.6-liter V6 in the little pickup produces 305 horsepower at 6,800 rpm, but the the tachometer indicates a redline at 6,500 rpm. So either he wasn't making as much power as he was promised, or the tachometer display was incorrect. Bearing said he asked Chevy about it but got no response. Until now. A General Motors spokesman said the rev limiter is indeed set for 6,800 rpm, but the tach graphics "are slightly off" in the Colorado and the GMC Canyon, and submitted an SAE horsepower certification to back him up. If you're wondering how such a thing got past quality control... well, let's just say you're not alone. GM is going to fix "the graphics on future trucks," which makes it sound like Bearing will just have to learn to live with the indicated redline he's got. He could always pretend he's driving a sleeper, with four more ponies waiting to be unlocked in the danger zone for those who dare. Related Video: Featured Gallery 2015 Chevrolet Colorado: First Drive View 38 Photos Related Gallery 2015 GMC Canyon: Quick Spin View 27 Photos News Source: Auto Guide Auto News Chevrolet GM GMC Truck gmc canyon