2014 Ltz Used 4wd Certified 5.3l V8 Trailer Brake Pickup Truck Bose Leather 4x4 on 2040-cars

Auto blog

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles

GM recalls half-million full-size SUVs to address seatbelt issue

GM is recalling its redesigned full-size SUV models to address improperly riveted mounts securing the third-row seatbelts that may fail in the event of an accident. The population includes the 2021-2022 Cadillac Escalade and Escalade ESV, 2021-2022 Chevrolet Suburban and Tahoe, and 2021-2022 model year GMC Yukon and Yukon XL, for a total of 484,155 vehicles. "Operators at the supplier’s manufacturing plant may have not properly followed manufacturing processes and inadvertently missed the rivet forming operation," GM said in its defect report to NHTSA. "In certain of these vehicles, the rivet that retains the buckle to the mounting bracket in the left or right side third-row seatbelt buckle assembly may not have been properly formed during the manufacturing process. If the third-row seatbelt assembly is not properly riveted, it may not properly restrain occupants in a crash, increasing the risk of injury." Fortunately, the fix is relatively simple. GM service technicians will inspect the rivets on the rear seatbelt buckle assemblies and replace the entire unit if the rivets are not to spec. Dealer notifications have already been distributed; owners should receive notice start in September. Related video: Cadillac Chevrolet GM GMC Ownership Safety SUV

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.