2014 Chevrolet Silverado 1500 1lt on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

General Motors and EVs: No stranger to firsts, but where's the leadership?

2015 is already shaping up to be the year of "affordable, 200-mile EV" concepts. Nissan and Tesla have each been talking about them for some time, the latter promising to unveil its Model 3 at the North American International Auto Show in January before balking when the time came. Instead, Chevrolet beat them all by unveiling the Bolt concept at the same event, followed shortly thereafter with suggestions of a 2016 launch – potentially offering the first nationwide EV with anything close to that range. It was the ballsiest EV-related move General Motors has made in a quarter century. But will it remain so? Exactly 25 years before the Bolt rolled up onto the turntable, then-Chairman Roger Smith unveiled GM's last ground-up EV concept, the even-more-unfortunately-named Impact, at the Los Angeles Auto Show in January 1990. A few months later, he surprised most of his colleagues by announcing its intended production in honor of Earth Day. It was the first modern foray into electric vehicles for the US by any automaker, one that was rewarded by the State of California with what is now known as the Zero Emissions Vehicle mandate. The program not only forced other automakers into competing with Roger's pet project, but inspired all of them to fight it like small children against bedtime. Some years later, the drivers themselves weighed in, with a biting documentary about that obstinance and the leadership it cost both GM and the country. Within months, GM was first back into the fray of plug-in vehicles. Many criticized the company for starting with a PHEV rather than jump straight back into EVs. The choice wasn't totally out of the blue – even EV1 was meant to be followed by a PHEV. And especially on the heels of Who Killed the Electric Car?, some skittishness was understandable: even a successful EV would invite a "we told you so" public reaction, underscoring their mistake in ending the EV1 program. If a new EV didn't do well, they'd be convicted in the public eye as serial killers. All while seeking a federal bailout. For all the flak, the resulting Chevy Volt was and is a better car than GM has ever gotten credit for. But the company seemed to grow weary of having to overcome its varied past, and while the current owners remain happy, much of the stakeholder and community engagement that so effectively built early goodwill and sales growth faded not long after launch. Marketing has been spotty in both consistency and effectiveness.

GM does not have to turn over its ignition switch documents

In June the lawyer representing plaintiffs suing General Motors over faulty ignition switches accused GM and its firm King & Spalding of working together to cover up the malfunction. Bob Hilliard said that certain communication between GM and King & Spalding from 2010 to 2013, mainly focused on three Chevrolet Cobalt crashes, would reveal that they conspired in "burying what they knew" concerning the defect, and furthermore that the law firm broke rules of professional conduct once it found out about "ongoing fraudulent concealment" at GM. Hilliard filed a motion in a Manhattan court to force GM and King to hand over the memos, which were protected by attorney-client privilege. Hilliard said that the alleged ongoing fraud should trump attorney-client privilege, a GM spokesman said at the time that the issues in question had already been discussed previously, and that plantiffs already had much of the communication Hilliard's motion sought. US District Judge Jesse Furman ruled in favor of GM and King, refusing to order the release of the communication. In spite of finding probable cause that GM was engaging in a crime or fraud by not revealing the ignition switch defect, Furman did not find cause to believe that GM and King's discussions at the time were centered around continuing that potential crime or fraud. Saying also that plantiffs already had many of the disputed documents, attorney-client privilege should hold sway over the remainder. The class action case goes to trial in January 2016.