2010 Ltz 6.2l Auto Black on 2040-cars

Auto blog

NHTSA investigating nearly 750,000 GM models over non-deploying airbags

Nearly 750,000 vehicles built by Chevrolet, GMC, and Cadillac are the subject of a National Highway Traffic Safety Administration (NHTSA) investigation due to non-deploying driver-side airbags. While the investigation is ongoing, the agency believes the issue is likely due to rust particles that form on the inflator's connection terminal interface. The list of nameplates included in the investigation includes Chevrolet's Silverado, Tahoe, and Suburban, GMC's Sierra, Yukon, and Yukon XL, plus Cadillac's Escalade, Escalade ESV, CT4, CT5, and XT4. All of the potentially affected vehicles are 2020 or 2021 models, according to a bulletin published on the NHTSA's website. Investigators launched the probe in April 2021 after 15 consumers reported airbag-related issues, including nine who said an airbag malfunction light appeared in the instrument cluster. More alarmingly, the NHTSA is aware of six accidents that caused significant damage to the car's front end yet didn't trigger the driver's airbag. It adds that there are no fatalities linked to the issue, but there are six crashes and eight injuries reportedly blamed on it. No evidence suggests this problem is related to the millions of potentially deadly Takata inflators recalled over the past few years. General Motors is aware of the defect. It sent a technical service bulletin (TSB) to its dealers in March 2021 to address the aforementioned warning light. The note explains the issue is due to "rust particles in the connection terminal interface of the driver's airbag inflator." The company hasn't issued a safety recall yet, however. Whether it will partially depends on the NHTSA's findings. It's currently looking into the scope and the severity of the problem, and it wants to understand its implications on driver safety. Investigators will decide whether General Motors needs to recall the 749,312 cars that are part of the probe when they close their investigation. General Motors has already spent a significant amount of money replacing defective airbag-related parts in its cars. In November 2020, it was ordered by the American government to recall nearly 6 million pickup trucks and SUVs equipped with potentially dangerous Takata airbag inflators. It repeatedly argued that testing proved the inflators were safe, and it petitioned the agency four times starting in 2016 to avoid a recall, which cost an estimated $1.2 billion (about a third of its net income in 2020).

Anti-purist 1963 Ferrari GTE sports hot rod Chevy V8

I remember reading a story around the time Fast and Furious: Tokyo Drift came out. It focused on one of the star cars of that film, a 1967 Ford Mustang fastback that started the film as a shell, and in a pinch, was transformed into a modified masterpiece, complete with the RB26DETT engine from a Nissan Skyline GT-R (which started the film under the hood of an S15 Silvia). There was a genuine (and in our minds, absurd) fear in the article that taking a piece of classic American iron and fitting a twin-turbocharged JDM engine would result in some awful trend in the classic car community. If you thought a GT-R-powered classic Mustang was sacrilege, though, this car will probably make you vomit. For the rest of us, it's a neat piece of engineering. Shown above is a 1963 Ferrari 250 GTE, and yes, that's a 302-cubic-inch, small-block Chevrolet V8 under the hood. On top of that, it uses the six-speed manual transmission from a Viper, a nine-inch Ford rear end, and Mitsubishi-sourced paint. So yeah, it's a FrankenFerrari. Check out Road Heads' interview with this custom GTE's owner, which is followed by a brief test drive. And of course, head into Comments afterwards, and let us know what you think. Is this Yankee-powered 250 GTE blasphemous or badass?

GM to invest $150 million in Flint to boost heavy-duty pickup production

FLINT, Mich. — General Motors President Mark Reuss said on Wednesday that the automaker is investing about $150 million at its Flint Assembly plant in Michigan to boost production of heavy duty trucks by another 40,000 vehicles a year. Reuss announced the investment at the Flint truck assembly plant wearing a United Auto Workers pin. The Detroit automaker had announced back in February it was adding 1,000 jobs in Flint to build a new generation of heavy-duty pickup trucks. GM did not say that the latest investment would add more jobs at the plant, but Reuss said there could be opportunities to add workers as the launch of the automaker's new trucks progresses. GM has been under pressure from President Donald Trump and lawmakers of both parties to add jobs in the United States after it said last November it would idle the Chevy Cruze assembly plant in Lordstown, Ohio, and likewise had no new products for three other U.S. manufacturing plants. The Flint investment will include upgrades to the plant's conveyors and other new tooling, and will be completed in the first half of 2020. GM has invested more than $1.6 billion in the plant since 2013. Last month, GM said it would invest $24 million to increase truck production at its assembly plant in Fort Wayne, Indiana, which makes Chevrolet Silverado and GMC Sierra models. Sales of heavy-duty pickups in the United States have grown to more than 600,000 vehicles a year, up more than 20 percent since 2013, according to industry data. Prices for luxury models can easily top $70,000. GM's Chevrolet and GMC brands have long trailed Ford's F-series heavy duty trucks in the lucrative segment. The new Chevrolet and GMC heavy duty trucks have been re-engineered to tow heavier trailers, and keep pace in what has become an arms race among the Detroit Three automakers to claim superior torque and towing capability. Related: Silverado HD vs. 2019 Ram, Ford heavy duty trucks: How they compare on paper