66 1966 Chevy Ii Nova 4 Speed Marina Blue Complete Restoration Sbc Super Slick!! on 2040-cars

Auto blog

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

NHTSA investigating nearly 750,000 GM models over non-deploying airbags

Nearly 750,000 vehicles built by Chevrolet, GMC, and Cadillac are the subject of a National Highway Traffic Safety Administration (NHTSA) investigation due to non-deploying driver-side airbags. While the investigation is ongoing, the agency believes the issue is likely due to rust particles that form on the inflator's connection terminal interface. The list of nameplates included in the investigation includes Chevrolet's Silverado, Tahoe, and Suburban, GMC's Sierra, Yukon, and Yukon XL, plus Cadillac's Escalade, Escalade ESV, CT4, CT5, and XT4. All of the potentially affected vehicles are 2020 or 2021 models, according to a bulletin published on the NHTSA's website. Investigators launched the probe in April 2021 after 15 consumers reported airbag-related issues, including nine who said an airbag malfunction light appeared in the instrument cluster. More alarmingly, the NHTSA is aware of six accidents that caused significant damage to the car's front end yet didn't trigger the driver's airbag. It adds that there are no fatalities linked to the issue, but there are six crashes and eight injuries reportedly blamed on it. No evidence suggests this problem is related to the millions of potentially deadly Takata inflators recalled over the past few years. General Motors is aware of the defect. It sent a technical service bulletin (TSB) to its dealers in March 2021 to address the aforementioned warning light. The note explains the issue is due to "rust particles in the connection terminal interface of the driver's airbag inflator." The company hasn't issued a safety recall yet, however. Whether it will partially depends on the NHTSA's findings. It's currently looking into the scope and the severity of the problem, and it wants to understand its implications on driver safety. Investigators will decide whether General Motors needs to recall the 749,312 cars that are part of the probe when they close their investigation. General Motors has already spent a significant amount of money replacing defective airbag-related parts in its cars. In November 2020, it was ordered by the American government to recall nearly 6 million pickup trucks and SUVs equipped with potentially dangerous Takata airbag inflators. It repeatedly argued that testing proved the inflators were safe, and it petitioned the agency four times starting in 2016 to avoid a recall, which cost an estimated $1.2 billion (about a third of its net income in 2020).

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.