1977 Chevrolet Nova on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Foreign automakers pay from $38 to $65 per hour to non-union workers

As leaders for the United Auto Workers gather in Detroit for their Special Convention on Collective Bargaining to work out the negotiating stance for this year's new labor agreements with the Detroit 3 automakers, what they most want to do is figure out how to eliminate the two-tier wage scale. However, the lower Tier 2 wage has allowed the domestic automakers to reduce their labor costs, hire more workers, and compete better with their import competition. As it stands, per-hour labor rates including benefits are $58 at General Motors, $57 at Ford, and $48 at Fiat-Chrysler – a reflection of FCA's much greater number of Tier 2 workers. The Center for Automotive Research released a study of labor rates (including benefits) that put numbers to what the imports pay: Mercedes-Benz pays the most, at an average of $65 per hour, Volkswagen pays the least, at $38 per hour, and BMW is just a hair above that at $39 per hour. Among the Detroit competitors, Honda workers earn an average of $49 per hour, at Toyota it's $48 per hour, Nissan is $42 per hour, and Hyundai-Kia pays $41 per hour. The lower import wages are aided by their greater use of temporary workers compared to the domestics. Automotive News says the ten-dollar gap between those foreign camakers and the domestics turns out to about an extra $250 per car in labor, which adds up quickly when you're pumping out many millions of cars. That $250-per-car number is one that, come negotiating time, the Detroit 3 will want to reduce, as the UAW is trying to raise both Tier 1 and Tier 2 wages. Another wrinkle is that the domestic carmakers are considering the wide adoption of a third wage level lower than Tier 2. Some workers who do minor tasks like assembling parts trays kits and battery packs already make less than Tier 2, but the UAW will be quite wary about cementing yet another wage scale at the bottom of the system while it's trying to fight a bigger battle at the top. News Source: Automotive News - sub. req., BloombergImage Credit: AP Photo/Erik Schelzig Earnings/Financials UAW/Unions BMW Chevrolet Fiat Ford GM Honda Hyundai Kia Mercedes-Benz Nissan Toyota Volkswagen labor wages collective bargaining labor costs

Next-generation GMC Canyon, Chevy Colorado spied together

With the debut of the next-generation GMC Canyon coming in a couple of months (in off-road-ready AT4 guise no less), it's no surprise that both it and the Chevy Colorado are out testing without the heavy coverings of early prototypes. One of our spy photographers caught examples of both trucks with close-fitting vinyl wraps. This gives us a great opportunity to see each pickup more clearly, but also to compare and contrast the designs. From the front, the GMC features a narrower, but seemingly taller grille. At the top are slender lamps. They seem to be daytime running lights, though, and below them are much larger units that will function as the actual headlights. The prototype shown seems to be one of the AT4 variants, based on the lack of a lower air dam and the opened up corners of each bumper. Small fog lights show up in the lower bumper, too. As for the Chevy, its grille is wider, and it blends into the headlights. The lights are at the top of the grille, and they seem to incorporate the actual headlights, not just running lamps. The grille mesh has some interesting detailing, and there are auxiliary lights below the main headlights. This one seems to be a more mainstream Colorado model since it still has a front air dam, possibly a Z71 model, considering the chunky tires. Not surprisingly, the two trucks are very similar from the sides and the rear. They have cabins that look lower, longer and more squared-off than the current models. The fenders look more punched out and aggressive, too. The main differentiator between the Chevy and GMC are the wheel openings. The GMC has sharp corners and the Chevy has more rounded ones, as is the case with the full-size trucks. As previously mentioned, the GMC Canyon AT4 will be revealed this summer, so likely in just a month or two. The Colorado will likely be revealed this summer, too. It's expected that it will use the turbocharged 2.7-liter four-cylinder shared with the Silverado. Naturally, it will be available with two- and four-wheel drive and a variety of trim levels including the AT4 and ZR2 off-road versions. Related video: