Jennifer R. Berman on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

New Chevrolet Silverado to be revealed on Facebook on Thursday

There's not much to see here, but if you're one of those waiting for the reveal of the 2014 Chevrolet Silverado 1500, above is the teaser image that Chevrolet posted on its Facebook page. We've seen the truck in form-fitting camo before, and even less can be made out here beyond those seriously punchy Silverado-esque fenders and the knowledge that the projector-beam headlamps teased previously do indeed work. We'll have to wait until Thursday for a full perusal of the "bold exterior design" and "careful attention given to every detail" we've been promised.
Gathering intel and rumors, magnesium and aluminum contribute to the Silverado's weight loss plan, the purported "High Country" top-tier trim will contribute to luxury pickup truck competition and profit margins and the next-generation small-block V8 will contribute to improved fuel economy. On the engine note, there have been rumors of available V6 engines, and when Facebook user John Jones asked "Where's your answer to that EcoBoost Chevy?", the Bowtie replied "stay tuned on the 13th. We think you'll be pleased...".
Along with the "Raise the Bar" tag, Chevrolet says of the Silverado, "You asked, we delivered." You can watch the reveal live on Chevrolet's Facebook page at 9:30 am EST, this Thursday, December 13. The GMC Sierra 1500 will also be there, and we'll see both in person at the Detroit Auto Show in January.

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.