1969 Chevrolet Chevelle, 69 Chevelle, 1969 Chevy on 2040-cars

Auto blog

Canada opens probe into 250,000 GM pickups, SUVs over brake performance

Transport Canada, the auto safety regulator, has opened a probe into braking issues in nearly 250,000 General Motors full-size pickups and SUVs after U.S. officials launched a similar probe last year, the agency said on its website. The U.S. National Highway Traffic Safety Administration (NHTSA) in November into 2.73 million U.S. 2014-2016 model year SUVs and pickups after receiving 487 reports of hard brake pedal effort accompanied by extended stopping distance that were attributed to deterioration of the engine-driven brake assist vacuum pump. Transport Canada's probe covers 249,700 2015 through 2017 model year vehicles including the Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe and GMC Yukon as well as 2014-2017 Chevrolet Silverado LD and GMC Sierra LD vehicles. The U.S. agency said it had reports of nine incidents of vehicles incurring damage as a result of colliding with another vehicle or fixed object at low speeds and reports of two injuries. NHTSA said if the pump fails to operate, the amount of brake power assist can be significantly reduced, extending vehicle stopping distance. The NHTSA sent GM an information request in a Feb. 7 letter. A GM spokesman said he had no update on the investigation. Reporting by David Shepardson; editing by Jonathan Oatis

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

There's an impending shortage of new trucks in America's heartland

URBANDALE, Iowa — Jerry Bill is worried the novel coronavirus could hurt business at the Des Moines auto dealership he runs, but not because of a shortage of buyers for the big Ram pickups on his lot. "Our biggest issue will be if we don't get more inventory," said Bill, general sales manager of Stew Hansen Chrysler Dodge Jeep Ram, which sells around 2,700 new vehicles a year in Urbandale, a suburb of Iowa's capital Des Moines. After a drop in sales in April when consumers stayed home, Bill expects pickup truck sales to end May similar to where they were a year earlier. And if demand remains strong, Bill said he will run out of popular models in June. Fiat Chrysler began slowly restarting Ram truck assembly lines on Monday after a two-month shutdown. The U.S. economy contracted in the first quarter at its sharpest pace since the Great Recession of 2007-2009 because of lockdown measures aimed at slowing the spread of the coronavirus. Economists warn the second quarter will be much worse. Still, far from the lockdowns of states like New York, Michigan or Ohio, dealerships like Stew Hansen have provided FCA and Detroit rivals General Motors and Ford a rare bright spot: strong sales of pickup trucks in America's heartland. Overall U.S. sales of cars and light trucks crashed to the weakest pace in 50 years last month. But sales of big Detroit brand pickups, particularly in southern and western states less affected by the outbreak, significantly outperformed the market, industry executives and analysts said. Pickup trucks are one of the most profitable automotive segments in the world. They account for a huge portion of the Detroit automakers' profits and formed a huge lure for Peugeot, which expects to merge with FCA by early 2021. The pressure is now on to boost pickup truck production and send vehicles to dealers in parts of the country with dwindling supplies. That is particularly true for GM, which is running short of certain truck models after losing 40 days of production to a strike last fall. "If you don't have what someone wants, they can choose to go to another brand," said Cox Automotive analyst Michelle Krebs. 'Easiest swap ever' Detroit automakers in March rolled out large discounts — such as interest-free loans for seven years — to keep vehicles rolling off dealer lots.