Chevrolet - Impala on 2040-cars

Auto blog

2019 Chicago Auto Show Truck Roundup: Toyota, Ford, Chevy and Ram bring it

The 2019 Chicago Auto Show features an array of heavy-duty trucks, smaller trucks, other kinds of trucks, and well, more trucks. That means new versions of the 2020 Chevy Silverado Heavy Duty and 2020 Ford F-150 Super Duty, a refreshed 2020 Toyota Tacoma and a trick tailgate on the 2019 Ram 1500. Sound a little crazy? Morgan Stanley research says 68 percent of passenger vehicles sold in the United States last year were classified as light trucks. So actually, bring on the trucks! Here's some impressions on the Chicago reveals, plus our take on the 2020 Subaru Legacy sedan. — Toyota updated the 2020 Tacoma with some light but useful enhancements. An improved infotainment has new audio features and larger screens. The grilles and wheels are different, but nothing drastic. Toyota still offers nice differentiation across the Tacoma lineup, and the design tweaks are subtle but thoughtful. Toyota tends to stretch out the Tacoma's generations, so it's wise to keep modifying and iterating to keep pace in this competitive segment. — Staying with Toyota, the Land Cruiser Heritage Edition is a legit special model that fans of this historic nameplate will appreciate. An anchor of the Toyota line in the United States since 1958, the Land Cruiser's roots date to Toyota's 1951 BJ Series military vehicle. Two colors, Midnight Black and Blizzard Pearl, are exclusive to this model and look slick against the blacked-trimmed grille and lightly bronzed wheels. Inside, bronze stitching is used on the steering wheel, seats, center console and other parts. The best part? Land Cruiser spelled out in script on the rear pillar. It's a limited model (1,200 units) and pricing isn't out yet, but that badge is probably why you buy this SUV. — The 2020 Chevy Silverado HD gets imposing looks that differentiate it from the light-duty range, an eye-popping max towing capability of 35,500 pounds and some updated powertrain elements. A new gas-fed V8 that serves as the entry point is one of the highlights, and the 6.6-liter mill makes 401 hp and 464 lb-ft, up significantly over the old 6.0-liter. There's also a new Allison 10-speed transmission teaming with the Duramax diesel to achieve that lofty max towing figure. With an updated trailering system and a larger cabin, the Silverado HD range is comprehensively remade to fight Ram and Ford. — The 2020 Ford Super Duty is also redone, and like the Chevy line, it gets a new gas V8 checking in at 7.3 liters.

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Chevy to resume engine-building program for 2015 Corvette Z06

One of Chevrolet's most popular and unique customer features is set to return for 2015, as the company has announced that the Engine Build Experience is back. Interested owners will be able to screw together their engines beginning in March. The $5,000 option (which does not include the cost of travel) will give future owners of the 2015 Corvette Z06 the chance to screw together their car's actual 6.2-liter, supercharged V8. Available on each of the Z06's three trims, the Engine Build Experience includes a day at the Performance Build Center, instruction from an engine assembly tech, photographs of the experience and a personalized engine plaque. Once the build process is completed, the engine will (eventually) be fitted under the hood of the customer's personal Z06. "Chevrolet recognizes the passion customers have for Corvette and the Engine Build Experience offers them a truly unique opportunity for hands-on involvement in the creation of the heart of their new car," Corvette product manager Harlan Charles. "It's important for customers to understand their engine won't be installed the day after they built it. It will flow into the scheduling process for vehicle assembly, which depends on a number of logistical variables." Scroll down for the official announcement of the Z06's Engine Build Experience, available below. Exclusive Corvette Engine Build Experience Returns Program renewed for supercharged LT4 engine at new Bowling Green build center 2015-01-07 BOWLING GREEN, Ky. – Chevrolet announced today it is resuming the exclusive Engine Build Experience for Corvette Z06 customers – the only program of its kind for supercar customers. Starting in March 2015, Corvette Z06 customers will be able to assemble the 650-hp supercharged LT4 engine for their cars at the new Performance Build Center inside the Bowling Green Assembly Plant. "Chevrolet recognizes the passion customers have for Corvette and the Engine Build Experience offers them a truly unique opportunity for hands-on involvement in the creation of the heart of their new car," said Harlan Charles, Corvette product manager. "It's a chance to bond with their new car." The Engine Build Experience is selected with order code PBC and is offered on all Z06 trim levels.