2014 Chevrolet Impala 2lt on 2040-cars

Auto blog

Recharge Wrap-up: Chevy Volt's new, improved powertrain; Inabikari wants to build Tesla Model X fighter

We knew the 2016 Chevrolet Volt's new powertrain would provide more range, but we didn't know how much. According to GM's Executive Director Larry Nitz, it is about 12 percent more, overall. "I can't think of a powertrain we've re-engineered more extensively within a five-year period than this one," he said. The battery, electric drive system and gasoline generator have all been reworked to allow for an overall driving range of up to 425 miles, with electric range speculated to reach 42 miles or more. The new Volt will also benefit from 20 percent quicker low-end acceleration, weight reductions and improvements in NVH. Read more at Hybrid Cars and at the SAE website. Hyundai's FCEV research and development boss, Dr. Sae-Hoon Kim, is optimistic about the future of hydrogen mobility in Japan. With the Tucson Fuel Cell already in production ahead of Toyota's FCV, Hyundai has a foothold in the hydrogen car scene. Kim believes that since the Fukushima disaster, Japan's attitudes toward energy make it friendly to a growing hydrogen economy. He also says that hydrogen won't be limited to Hyundai, with Kia getting all the battery EVs. "Both types are for both companies," Kim says. "For the moment, volumes are small and it is not wise to have Hyundai and Kia competing." Read more at Just Auto. The Latvian/German startup Inabikari is using crowdfunding to build an electric crossover for Europe. The Rev.01 EV hopes to compete with Tesla's upcoming Model X with a range of over 400 miles and a five-second 0-60 time. The group currently is trying to raise initial funds through an Indiegogo campaign, with hopes of more investment in the future and sales beginning in 2017. See the video below, and read more at Hybrid Cars and at the Inabikari website. Fuel economy and emissions regulations could lead to some interesting design changes to automobiles. The World Light Duty Test Procedure, set to replace the New European Driving Cycle in 2017, will push automakers to find new ways to reduce drag on their vehicles. For better aerodynamics, we could see traditional side-view mirrors replaced by cameras that display what they see on screens inside the vehicle. Another likely change will be the introduction of smaller, narrower wheels. Improving the average drag coefficient from 0.32 to 0.20 could reduce CO2 emissions by as much as 20 percent. Read more at Automotive News Europe.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM applies for LT5, LTX trademarks... are new small block variants coming?

Recently discovered General Motors trademark applications for LT4, LT5, LT88 and LTX have observers wondering what kind of high-performance offerings could be on their way. A new LT4 would mark a return of the engine designation first used on the Corvette Grand Sport, SLP Pontiac Firehawk and SLP Chevrolet Camaro SS from 1996 and 1997. Supposition at Corvette Forum - which provided advance intel on the C7 like these leaked images - believes a new LT4 could go into the high-performance trim of the next-gen, 2015 Camaro that would be more powerful than the 580-horsepower Camaro ZL1.
Seeing an LT5 again would also be déjà vu - in its former life it was a 5.7-liter V8 for the C4 Corvette ZR-1 from 1990-1994 designed by Lotus, producing from 370 hp to 405 hp. A mix of rumor and hope is that the new LT5 will be a supercharged evolution of the 6.2-liter LT1 (pictured) placed in the new C7 Corvette, and that it will go into the C7 version of the ZR1 pumping out something like 700 hp.
The LTX trademark is, as with that last letter, a complete mystery. If the "X" isn't a generic way to denote the whole LT family, it's wondered if it LTX could refer to a crate motor offering like the LSX.