1992 Chevrolet Corvette Base Convertible 2-door 5.7l on 2040-cars

Auto blog

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video:

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Chevrolet Malibu gets across-the-board price cuts, hopes to dig out of slump

To say that things aren't going well for the newly redesigned 2013 Chevrolet Malibu is a pretty sizable understatement. Reports have been swirling about the Malibu getting an emergency design refresh, less than a year after its introduction, as well as having its production at the Fairfax Assembly Plant halted twice already this year for excessive inventory. Now, Motor Trend is reporting that the midsize sedan will be receiving price drops across the board ranging from $300 on a number of models up to $770 on the 1LT trim; offsetting some of MSRP drop, though, the destination charge has increased from $760 to $810.
Without destination, the entry-level Malibu LS now starts at $21,995, which is still about $300 more than a Honda Accord and about $300 less than the segment's top-selling Toyota Camry. This new pricing also drops the price of the Eco, 2LT and 3LT trims by $300. The LTZ trim has dropped by $415, meaning that the Malibu's top dog now starts at just under $30,000, excluding destination.
Here are the new starting prices for all eight of the Malibu trim levels compared to the previous prices for the 2013 model year (including destination):