1965 Chevrolet Corvair on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Fingers point to dragged-out NHTSA investigation after second death by ARC airbag inflator

Safety advocates have increased criticism of the federal government's National Highway Traffic Safety Administration after an exploding airbag inflator that's been under investigation for more than six years killed a second person.  On Wednesday, NHTSA posted recall documents filed by General Motors that revealed the second death, the driver of a 2015 Chevrolet Traverse SUV with an inflator made by Tennessee company ARC blew apart, spewing shrapnel. No details were given about where and when the death occurred. NHTSA has said that ARC Automotive of Knoxville has manufactured about 8 million inflators used nationwide in vehicles made by General Motors, Fiat Chrysler (now Stellantis), Kia and Hyundai. “NHTSA should have been all over this along time ago,” said Rosemary Shahan, president of California-based Consumers for Auto Reliability and Safety. “There's just no denying that itÂ’s a (safety) defect.” NHTSA, the agency charged with with keeping America's automobiles and roads safe, began investigating ARC inflators in July of 2015 after two people were injured by flying shrapnel. The investigation became more urgent in 2016, when a Canadian woman driving an older Hyundai Elantra was killed by metal airbag fragments. Public records show only a little progress on the probe. In April, the agency posted a memo in saying it was reviewing volumes of information it received from ARC. Safety advocates such as Shahan say that the dragged-out investigation is an example of the deadly consequences that can result from an understaffed and underfunded agency. The second death should not have happened, Shahan said, and vehicles with faulty ARC inflators should have been recalled faster. The agency, Shahan said, is “grossly underfunded," but it still should have sought recalls of the ARC inflators. She said historically NHTSA has taken little action during Republican administrations but has ramped up safety efforts when Democrats control the White House. Messages were left Wednesday by the Associated Press seeking comment from NHTSA and ARC. At this time, relatively few vehicles are effected. The GM recall covers only 550 Chevy Traverse SUVs from the 2013 through 2017 model years, as well as Buick Enclave SUVs from 2008 through 2017. The automaker said in a statement that the faulty front driver's airbag inflators were either installed at the factory or in replacement airbag modules.

Suzuki recalls 2 million cars globally

Suzuki is recalling two million vehicles across the globe, including a number of Chevrolet Cruze sedans that it builds for General Motors, because the ignition switches may begin to smoke. None of the Cruzes being recalled were sold in the US, though. This recall is limited to the Japanese, European and Australian markets. In Suzuki's home market, 1,873,000 vehicles are being recalled, including the Cruze and a number kei cars built for Mazda (the Carol and AZ-Wagon), as well as the automaker's own Alto, Wagon R and Swift. Affected vehicles were built between 1998 and 2009. The remaining 133,000 vehicles include Cruzes and other Suzuki products sold in Europe and Australia. There have been no reports of injuries or accidents due to the 67 reported incidents, all of which come from the Japanese market, a Suzuki spokesperson told Automotive News. Related Video: