4x4 Lt W/2lt 5.3l Cd Power Outlets 2 Auxiliary With Covers 12-volt Air Dam Ebony on 2040-cars

Auto blog

Chevrolet planning new crossover between Equinox and Traverse

Chevrolet is taking a crowbar to its crossover lineup so it can slide in a new entry between the Equinox (shown) and the Traverse, according to a report in Automotive News. The current Equinox, a tweener compared to its rivals, will get smaller when the next-generation vehicle moves to the Delta platform that underpins the Chevrolet Cruze. The next Traverse will remain full-size, the liberated space between it and the smaller Equinox making room for a fourth offering from the brand. Designed on a short-wheelbase version of the Traverse platform, AN's sources say it will offer three-row seating, and its architecture will also serve the Cadillac SRX successor, the XT5, and the redesigned GMC Acadia. Yes, the Acadia will also come down a notch in size. Once all the rationalizing is complete, the Trax, Equinox, new crossover, and Traverse would give consumers a quicker, easier way to compare size and features with the competition. As it stands, the Ford Edge, Nissan Murano, Honda Pilot, and Toyota Highlander are all larger than the Equinox. The future offering and its two- and three-row seating options would take clear aim at those four vehicles, and the Equinox could focus on the Ford Escape, Honda CR-V, Toyota RAV4, and Jeep Cherokee segment. The new Chevy is predicted to go on sale at the end of next year as a 2018 model. Related Video: Featured Gallery 2015 Chevrolet Equinox View 14 Photos News Source: Automotive News - sub. req. Chevrolet Crossover cadillac srx gmc acadia chevy traverse cadillac xt5

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM won't really kill off the Chevy Volt and Cadillac CT6, will it?

General Motors is apparently considering killing off six slow-selling models by 2020, according to Reuters. But is that really likely? The news is mentioned in a story where UAW president Dennis Williams notes that slumping US car sales could threaten jobs at low-volume factories. Still, we're skeptical that GM is really serious about killing those cars. Reuters specifically calls out the Buick LaCrosse, Cadillac CT6, Cadillac XTS, Chevrolet Impala, Chevrolet Sonic, and the Chevrolet Volt. Most of these have been redesigned or refreshed within the past few model years. Four - the LaCrosse, Impala, CT6, and Volt - are built in the Hamtramck factory in Detroit. That plant has made only 35,000 cars this year - down 32 percent from 2016. A typical GM plant builds 200,000-300,000 vehicles a year. Of all the cars Williams listed, killing the XTS, Impala, and Sonic make the most sense. They're older and don't sell particularly well. On the other hand, axing the other three seems like an odd move. It would leave Buick and Cadillac without flagship sedans, at least until the rumored Cadillac CT8 arrives. The CT6 was a big investment for GM and backing out after just a few years would be a huge loss. It also uses GM's latest and best materials and technology, making us even more skeptical. The Volt is a hugely important car for Chevrolet, and supplementing it with a crossover makes more sense than replacing it with one. Offering one model with a range of powertrain variants like the Hyundai Ioniq and Toyota Prius might be another route GM could take. All six of these vehicles are sedans, Yes, crossover sales are booming, but there's still a huge market for cars. Backing away from these would be essentially giving up sales to competitors from around the globe. The UAW might simply be publicly pushing GM to move crossover production to Hamtramck to avoid closing the plant and laying off workers. Sales of passenger cars are down across both GM and the industry. Consolidating production in other plants and closing Hamtramck rather than having a single facility focus on sedans might make more sense from a business perspective. GM is also trying to reduce its unsold inventory, meaning current production may be slowed or halted while current cars move into customer hands. There's a lot of politics that goes into building a car. GM wants to do what makes the most sense from a business perspective, while the UAW doesn't workers to lose their jobs when a factory closes.