1970 Chevelle Ss on 2040-cars

Auto blog

First 2015 Chevy Corvette Z06 engine blows up at just 891 miles

You've waited and watched and waited some more for the arrival of your 650-horsepower, $78,000 Chevrolet Corvette Z06. Finally, that joyous day arrives and you eagerly, but gingerly, begin to break-in the 6.2-liter supercharged V8 monster under your hood. Then 900-odd miles after delivery, your excitement grinds, quite literally, to a halt. That's what the owner of one 2015 Z06 claimed happened to him when a simple break-in drive resulted in a lunched engine. The owner, known as Lawdogg149 on Corvette Forum, says he was out breaking-in his car ahead of a January track event when it happened. "While making a pull from 35 miles per hour, I accelerated and shifted short of redline, and boom - the car began knocking. I pulled over and popped the hood. I could hear a loud knock coming from the No. 6 cylinder area along with a serious, grinding, metal-on-metal sound coming from the supercharger area," Lawdogg wrote. A subsequent trip to the dealer confirmed his concerns, with the service facility telling Lawdogg that the No. 6 valvetrain had failed. The dealer couldn't research the issue further, though, as General Motors requested the engine be returned for a more thorough evaluation. The good news for the Z06's unlucky owner, at least, is that GM will be covering the engine replacement under warranty, an expense that Corvette Forum estimates is a nearly $24,000 procedure. At this point, the two leading theories behind the engine's detonation involve a manufacturing defect – which could be why GM is so keen to tear the blown powerplant down – or a mistake on the part of Lawdogg. As Motor Authority points out, such an error could be something as simple as the Z06's owner accidentally shifting to first rather than third during his 35-mph pull. If, however, there's a deeper manufacturing problem with the Z06's engine, this might not be the only case we end up hearing about.

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

GM to build next-gen Chevy Cruze in Mexico

As one of its global products, General Motors builds the Chevy Cruze for local consumption at assembly plants around the world: in Australia, South Korea, Vietnam, Thailand, China, India, Kazakhstan, Russia, Brazil and Ohio. The automaker is expected to trim those locations for the next generation of its compact sedan, but its latest announcement has it adding a new site to the list: Mexico. As part of a $350-million investment, GM's plant at Ramos Arizpe in Coahuila will gear up for production as one of several sites that will be charged with building the next-gen Cruze. The General has yet to announce just which plants those will be, but it has confirmed that the Lordstown, Ohio, site will once again be among them. The plant in St Petersburg, Russia, which has produced the current Cruze, is being shut down, as is the Holden plant in Elizabeth, Australia. The Ramos Arizpe assembly plant currently puts together the Chevy Sonic and Captiva as well as the Cadillac SRX, but has over the course of its 34-year history handled a variety of models for the Chevy, Pontiac, Buick, Cadillac, Saturn, Opel and even Saab brands. The site handles a quarter of GM's production in Mexico, and exports 87 percent of its capacity to other markets. Invertira GM 350 mdd en Ramos Arizpe para fabricar siguiente generacion de Chevrolet Cruze 2015-03-23 - Se consolida GM de Mexico como el sexto productor global de vehiculos para General Motors Company Ramos Arizpe, Coahuila - General Motors de Mexico anuncio este dia que invertira 350 millones de dolares en su Complejo de Manufactura Ramos Arizpe, para fabricar en estas instalaciones la siguiente generacion del modelo Chevrolet Cruze. "Esta inversion, que forma parte de los 5 mil millones de dolares anunciados en diciembre pasado para todo el pais, fortalecera la presencia de GM Ramos Arizpe en la produccion de nuestra compania a nivel mundial y, por supuesto, consolidara a Mexico como el sexto productor de automoviles para GM Company, con el 7% de la produccion global", informo Ernesto M. Hernandez, Presidente y Director General de GM de Mexico. En una reunion de trabajo en la que participaron Ruben Moreira, Gobernador del Estado de Coahuila y Rogelio Garza, Subsecretario de Industria y Comercio del Gobierno Federal, el Presidente de General Motors en el pais aseguro que el Complejo GM Ramos Arizpe se ha consolidado como un iman para las inversiones de la compania a nivel global. Adicionalmente, Ernesto M.