Find or Sell Used Cars, Trucks, and SUVs in USA

1970 Chevell Ss Clone on 2040-cars

US $16,500.00
Year:1970 Mileage:17000
Location:

Ocala, Florida, United States

Ocala, Florida, United States
Advertising:

1970 Chevelle SS clone 454 30 over ,motor has less then 300 miles ,Needs minor paint repair.

Auto Services in Florida

Y & F Auto Repair Specialists ★★★★★

Auto Repair & Service, Wheel Alignment-Frame & Axle Servicing-Automotive, Auto Transmission
Address: 5130 NW 15th St, Lauderdale-Lakes
Phone: (954) 978-7799

X-quisite Auto Refinishing ★★★★★

Automobile Body Repairing & Painting
Address: 1300 W Industrial Ave, Greenacres
Phone: (561) 292-3174

Wilt Engine Services ★★★★★

Auto Repair & Service, Engine Rebuilding & Exchange, Automobile Machine Shop
Address: 2202 D R Bryant Rd, Zephyrhills
Phone: (863) 858-4054

White Ford Company Inc ★★★★★

Auto Repair & Service, New Car Dealers, Automobile Body Repairing & Painting
Address: Kingsley-Lake
Phone: (352) 493-4297

Wheels R US ★★★★★

Auto Repair & Service
Address: 920 N US Highway 17 92, Winter-Park
Phone: (407) 699-9993

Volkswagen Service By Full Throttle ★★★★★

New Car Dealers, Automobile Repairing & Service-Equipment & Supplies, Brake Repair
Address: 6956 Edgewater Dr, Fern-Park
Phone: (407) 253-9081

Auto blog

GM recalls select Tahoes, Yukons, Escalades for rear driveshaft issue

Mon, Feb 7 2022

GM is recalling a number of its full-size SUVs due to an issue with the rear driveshaft assembly that could ultimately result in driveshaft failure. The actual number of total vehicles involved in the recall is small at just 1,789, but it’s spread out across the entire 2021 model year full-size GM vehicle lineup. That means a small number of every model is being recalled, including the Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL and the Cadillac Escalade and Escalade ESV. GM traced the issue back to certain driveshaft assemblies with ball bearings that were not properly heat treated. If theyÂ’re not properly heat treated, GM says that the balls may deform over time, causing noise and vibration. Continue to drive in this condition, and GM says the affected joint in the driveshaft assembly could seize, causing loss of drive power. However, the problem wonÂ’t present itself all at once, as GM says there will be a gradual increase of noises and vibrations before total failure. For those few owners with affected vehicles, GM says that it will replace the left and right rear driveshaft assemblies with properly-built units. Per usual with recalls, this will be done at your local dealership at no cost to the owner. If you have one of the recalled SUVs, expect to be notified mid-March. Related video:

5 reasons why GM is cutting jobs, closing plants in a healthy economy

Tue, Nov 27 2018

DETROIT — Even though unemployment is low, the economy is growing and U.S. auto sales are near historic highs, General Motors is cutting thousands of jobs in a major restructuring aimed at generating cash to spend on innovation. It's the new reality for automakers that are faced with the present cost of designing gas-powered cars and trucks that appeal to buyers now while at the same time preparing for a future world of electric and autonomous vehicles. GM announced Monday that it will cut as many as 14,000 workers in North America and put five plants up for possible closure as it abandons many of its car models and restructures to focus more on autonomous and electric vehicles. The reductions could amount to as much as 8 percent of GM's global workforce of 180,000 employees. The cuts mark GM's first major downsizing since shedding thousands of jobs in the Great Recession. The company also said it will stop operating two additional factories outside North America by the end of next year. The move to make GM get leaner before the next downturn likely will be followed by Ford Motor Co., which also has struggled to keep one foot in the present and another in an ambiguous future of new mobility. Ford has been slower to react, but says it will lay off an unspecified number of white-collar workers as it exits much of the car market in favor of trucks and SUVs, some of them powered by batteries. Here's a rundown of the reasons behind the cuts: Coding, not combustion CEO Mary Barra said as cars and trucks become more complex, GM will need more computer coders but fewer engineers who work on internal combustion engines. "The vehicle has become much more software-oriented" with millions of lines of code, she said. "We still need many technical resources in the company." Shedding sedans The restructuring also reflects changing North American auto markets as manufacturers continue to shift away from cars toward SUVs and trucks. In October, almost 65 percent of new vehicles sold in the U.S. were trucks or SUVs. That figure was about 50 percent cars just five years ago. GM is shedding cars largely because it doesn't make money on them, Citi analyst Itay Michaeli wrote in a note to investors. "We estimate sedans operate at a significant loss, hence the need for classic restructuring," he wrote. The reduction includes about 8,000 white-collar employees, or 15 percent of GM's North American white-collar workforce. Some will take buyouts while others will be laid off.

GM struggles to sell small cars, plans to lay off 2,084 employees at two plants

Thu, Nov 10 2016

Due to low demand for some of its vehicles, General Motors plans to cut 2,084 jobs at its assembly plants in Lordstown, OH and Lansing, MI. At the same time, the automaker also announced plans to invest approximately $900 million in three of its facilities – the Toledo Transmission Operations in Ohio, Bedford Casting Operations in Indiana, and Lansing Grand River in Michigan - for future products. GM will discontinue the third shift at both the Lansing Grand River plant and the Lordstown, OH plant. The Cadillac ATS, Cadillac CTS, and Chevrolet Camaro are made at the automaker's plant in Michigan, which currently has 2,700 employees. The move to eliminate the third shift affects 810 hourly workers, as well as 29 salaried employees, starting on January 16th. The plant in Lordstown, OH currently has 4,500 employees and makes the Chevrolet Cruze sedan. The plan to discontinue the third shift will affect 43 salaried workers and 1,202 hourly employees and will start on January 23rd. As Fortune points out, sales of the Cruze are down 20 percent through October, while sales of the Cadillac ATS and CTS were down 17 percent through the same period of time. In addition to cutting the third shift at both assembly plants, the automaker plans to invest a total of $900 million between three of its facilities for unnamed future products. GM's Toledo Transmission Operations will receive $667.6 million, the Lansing Grand River Assembly plant will receive $211 million, and the automaker's Bedford Casting Operations will get $37 million. Last year, GM cut roughly 500 jobs from its Orion Township factory due to slow sales of the Chevrolet Sonic and Buick Verano, with surging crossover and SUV sales as the most likely culprit. With GM posting much healthier sales figures for the Chevrolet Equinox and Cadillac XT5 compared to the ATS, CTS, and Cruze, it looks like compact SUVs are to blame for this year's layoffs as well. Related Video: News Source: Fortune, General MotorsImage Credit: REUTERS / Rebecca Cook Hirings/Firings/Layoffs Plants/Manufacturing Cadillac Chevrolet GM Coupe Sedan Lordstown Ohio