Hot Wheels Special Edition V8 Leather Head Up Navigation 21" Wheels Automatic on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Cadillac Celestiq, Lyriq, Hummer, other future GM electric cars: Here's everything we saw at ‘EV Day’

WARREN, Mich. — Today, General Motors held an “EV Day” event at its Warren, Michigan, campus to present its new “Ultium” battery technology, modular electric vehicle architecture and soon-to-come electric vehicles. Unfortunately, we were forbidden from bringing cameras into the event, so while we canÂ’t show you what we saw, we can tell you more about it. While we saw the previously teased Cadillac EV (which we now know to be called the Lyriq) and the GMC Hummer pickup teased during the Super Bowl, there were a number of other future cars at the event, which GM President Mark Reuss assured us are all real vehicles in the works. The biggest surprise came at the end of the event, though, in the Cadillac Celestiq electric sedan, which Reuss described as a future flagship that would be hand-built “very locally.” It had been hiding under a dark sheet all morning, with the front and rear illuminated Cadillac emblems shining from underneath. When the wraps came off, we saw a long, white, four-seat fastback sedan. The 23-inch wheels were pushed out to the very corners of the car, giving it what appeared to be a very long wheelbase. The model on the stage had no side mirrors or visible door handles. The grille mirrored that of the Lyriq crossover next to it, with integrated lighting in lieu of the usual mesh or slats youÂ’d see in an internal combustion car. The entire roof, all the way until it tapered to the tail of the vehicle, was tinted glass. In back, vertical tail lighting ran down the C-pillar before turning rearward across the top of the trunk. Inside, everything below the beltline of the windows — essentially all but the headrests and top portion of the steering wheel, was hidden from view. Behind the Celestiq, a large digital display showed a rendering of its interior. The dash consists of a pillar-to-pillar curved LED display serving as both instrument panel and infotainment system. Protruding forward between the front seats was another touchscreen that appeared to house some more controls, with open area, probably for storage, below it. The rear seats had the same sort of touchscreen between them. Built into the back of the front seats were a pair of rear-seat entertainment screens, much like we saw in the Lyriq. The door panels blended wood, metal and animated lighting to give character and a sense of opulence. GM interior design manager Tristan Murphy was on hand to tell us a bit more about the Celestiq.

GM and Isuzu to partner for medium-duty commercial truck

General Motors is returning to the medium-duty truck business in the US for the first time since 2009 thanks to a new deal with longtime-partner Isuzu. The arrangement brings the Isuzu N-series models to Chevrolet dealers with the Bowtie's branding on them in 2016. There are six medium-duty Chevy models arriving at dealers in regular cab and crew cab bodies: the 3500, 3500HD, 4500, 4500HD, 5500, and 5500HD. The trucks will be sold as a bare chassis for buyers to outfit to their needs. Depending on model, customers will have the choice of an Isuzu-sourced 3.0-liter and 5.2-liter diesel engines or a 6.0-liter V8 gasoline-fueled engine from GM and six-speed gearbox. According to company spokesperson Bob Wheeler to Autoblog, the diesel models will be built in Japan and the rest assembled from knockdown kits in Charlotte, MI. This kind of vehicle sharing isn't uncommon for GM in the commercial segment, and it already partners with Nissan to use the Japanese brand's NV200 as the City Express van. The General also once owned a significant stake in Isuzu, and the two have remained collaborators even since then. Isuzu and GM Enter Commercial Vehicle Collaboration Agreement in the U.S. 2015-06-15 DETROIT and FUJISAWA, Japan – General Motors Co. (NYSE: GM) and Isuzu Motors (TSE 7202) have reached an agreement on a U.S. commercial vehicle collaboration, allowing Isuzu to strengthen its product lineup and GM to expand its commercial vehicle portfolio. Isuzu will produce low cab forward models for GM, based off of the Isuzu N-Series. The vehicles will be distributed by participating Chevrolet dealers in the U.S. market starting in 2016. To strengthen the product lineup, GM and Isuzu will explore the use of GM commercial vehicle components for Isuzu low cab forward trucks and GM will continue to produce and supply the 6.0L V-8 gas engine and six-speed transmission for Isuzu gasoline-powered low cab forward trucks. Isuzu and GM have maintained a strategic partnership for more than 40 years, producing collaborative business opportunities throughout the world. This agreement continues that tradition and reinforces a long-term relationship that helps to explore future collaborations in the U.S. commercial vehicle business. About General Motors General Motors Co. (NYSE:GM, TSX: GMM) and its partners produce vehicles in 30 countries, and the company has leadership positions in the world's largest and fastest-growing automotive markets.