1966 Chevy C/10 on 2040-cars

Auto blog

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

GM recalls 3,300 pickups and SUVs for new ignition-switch issue [UPDATE]

UPDATE: A statement from GM about the recall has been added below. The exact total of vehicles affected is 3,296, including 3,073 of them in the US. General Motors isn't letting an ignition-switch problem grow into a massive scandal again. The automaker is recalling about 3,300 North American trucks and SUVs. They are: the 2014 Chevrolet Silverado and GMC Sierra and the 2015 Chevy Suburban and Chevy Tahoe, as well as 2015 model heavy-duty pickups, the Detroit News reports, citing an Associated Press story. The issue appears to have been caught fairly quickly. In this case, the keys can get stuck in the "start" position and then slip to "accessory" if bumped. This is because the ignition lock gears have an outer diameter that's larger than the specifications allow. When that happens the engine shuts off, and the driver loses assistance to the steering and brakes. The airbags might also be affected. The vehicles get a new ignition-lock housing to fix the problem. According to the Detroit News, an employee who experienced the problem with the switch discovered the issue, and this person then let officials at the automaker know as part of the Speak Up for Safety program. A total of five reports of the fault were discovered. However, there are no cases of injuries or crashes. The claims to the automaker's resolution program eventually tallied that GM's previous ignition switch problem included 124 deaths and 275 injuries. The company also had to recall millions of vehicles and pay significant fines to the US government. GM Statement General Motors is recalling 3,073 full-size trucks from the 2014 and 2015 model years in the U.S. Some of these vehicles may have an ignition lock actuator gear with an outer diameter that exceeds specifications, which may make turning the ignition key difficult. The ignition key could get stuck in the "start" position. This may be more likely at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the "start" position, and the vehicle experiences a significant jarring event or the vehicle's interior temperature cools, the ignition lock cylinder could move out of the "start" position, rotate past the "run" position, and move into the "accessory" position, leading to loss of power steering assist, power brakes and potentially air bag deployment in certain crashes. Dealers will replace the ignition lock housing.

Chevy confirms 2016 Camaro will have wheels, brakes

Good news, everyone! Chevrolet has issued yet another round of teaser images and information about the sixth-generation Camaro, set to debut in Detroit on May 16. This time around, Chevy's teaser images confirm that the new car will not only have wheels and tires (Goodyear Eagle F1s, no less), but brakes as well. On top of that, we now know that the new Camaro will be 28-percent stiffer than the outgoing model. "The more rigid body structure allowed the engineers to more precisely calibrate the steering and suspension systems because they didn't have to compensate for chassis flex. The lighter structure also enabled the size and mass of elements such as the wheels, tires and brakes to be scaled accordingly," GM said in a press release, which you can read below. We've already learned that the new coupe will be 200 pounds lighter than its predecessor, has a bunch of unique parts, and according to GM's Mark Reuss, will outperform the Ford Mustang in every way. Now, it's only a matter of time before we see the sixth-gen Camaro, but surely not before Chevy issues even more teasers and information. Related Video: 2016 Camaro is Stronger, Lighter and More Responsive Computer aided engineering contributes to 28 percent greater structural stiffness DETROIT – The engineering team spent 9 million hours of computational time honing the driving experience of the all-new 2016 Chevrolet Camaro before the first prototype turned a wheel. The structural modeling led to the Gen 6 Camaro being 28 percent stiffer than the current model. "The modeling abilities of computer aided engineering are advancing at incredible rates," said Jim Karlavage, Camaro program engineering manager. "Today, we can accurately model opportunities to add torsional strength without adding unnecessary mass. The result is a lighter, stiffer structure that benefits every aspect of the driving experience." The more rigid body structure allowed the engineers to more precisely calibrate the steering and suspension systems because they didn't have to compensate for chassis flex. The lighter structure also enabled the size and mass of elements such as the wheels, tires and brakes to be scaled accordingly. "The structural weight savings are compounded by opportunities to reduce un-sprung weight," said Karlavage.