1962 Chevy C-10 Shortbox Fleetside Rare Hotrod Streetrod on 2040-cars

Auto blog

GM's labor deal with UAW union on verge of ratification

Nov 15 (Reuters) - General Motors' tentative labor deal with the United Auto Workers (UAW) union closed in on ratification as the votes were counted on Wednesday. Following the approval earlier in the day by more than 60% of union members at the Detroit automaker's large Arlington, Texas, assembly plant, additional votes in favor have the deal close to clinching majority approval. The number of union locals, most of which are smaller, still to report vote totals is not large. After several large assembly plants voted against the deal earlier on Wednesday, some media had reported the deal was heading toward failure. But Arlington's support, followed by strong voting in favor by smaller warehouse and parts facilities, has put the deal on the brink of approval. This would mark the first ratification of a deal, which runs through April 2028, with one of the Detroit Three automakers. Ford and Stellantis voting is still under way, and workers at both companies were favoring ratification by comfortable margins. The UAW's GM vote tracking site currently shows approval of the contract leading by a 54% to 46% margin with almost 32,000 workers having cast votes out of about 46,000 UAW-represented GM workers. The Arlington plant, with about 5,000 UAW members, has the most of any GM plant. Voting officially ends on Thursday at 4 p.m. EST, although most votes will be cast on Wednesday. The UAW went on strike for more than six weeks against the Detroit Three, seeking better wages, working conditions and cost-of-living adjustments. All three companies agreed to tentative agreements about two weeks ago. Workers at other GM assembly plants voted against the deal, including 60% of workers at its Fort Wayne, Indiana, truck plant, 53% at its Wentzville, Missouri, plant, 58% of workers at GM's Lansing Grand River plant and 61% of workers at the Lansing Delta Township plant. Seven of GM's 11 assembly plants rejected the deal. In addition to Arlington, workers at plants in Detroit, Fairfax, Kansas; and Lake Orion, Michigan; approved the agreement. Only nine facilities are still listed without vote totals on the UAW vote tracker, including GM's Lockport, New York, components plant with about 1,200 members. Those voting in favor of the agreement have a lead of almost 2,500 and many of the facilities still to come include workers who stand to receive large pay increases upon ratification.

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

General Motors reportedly considering small electric pickup

General Motors is considering adding a small entry-level model to its range of electric pickups, according to a recent report. The carmaker is currently showing a prototype to a select group of customers to gather feedback about the model before executives decide its fate. Industry trade journal Automotive News claims that it saw the pickup during a workshop organized by General Motors and describes it as being "smaller than the Ford Maverick and the Hyundai Santa Cruz." For context, the Maverick stretches about 200 inches long, 73 inches wide, and 69 inches tall, so it's around 12 inches shorter, 11 inches narrower, and 10 inches lower than the recently-unveiled Chevrolet Colorado. It sounds like this little GM truck would be closer in size to the Brazilian-market Chevy Montana, pictured at top. But unlike the Montana, the model that Automotive News got a look at had two doors, a "low roofline," a four- to four-and-a-half-foot cargo box, and a design described as futuristic and sporty. If launched, the yet-unnamed pickup would be marketed as an "affordable" EV with a base price pegged under $30,000. However, that's a big if: the pickup — whose name hasn't been announced — hasn't been approved for production. "We're creating these to get a reaction and then to try to modify it or move on," Michael Pevovar, the director affordable EV and crossover design for Chevrolet, told the publication. "The input may come back that it's just too small, and that's okay," he added. If it turns out to be too small for buyers, General Motors hasn't ruled out building its entry-level electric pickup on a different architecture to make it a little bigger. It's too early to tell where the electric pickup would slot in the General Motors portfolio if executives approve it. Chevrolet immediately comes to mind, especially considering the sub-$30,000 price point. The model would make more sense with a bowtie on its front end than with a Cadillac emblem, GMC's trucks are normally positioned higher than Chevrolet's, and Buick hasn't built a pickup in many decades. Similarly, there's no word on when it would enter production or where it would be built. With that being said, there's very clearly a market for affordable, small pickup trucks. As of the third quarter of last year, Ford had sold more Mavericks than it had the Expedition or the Ranger. Hyundai hasn't sold as many Santa Cruz trucks, but it's still not too shabby, having beaten out the Venue and Accent last year.