1989 Chevrolet Blazer K10 on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

GM under fire from safety advocates over braking problem caused by recall fix

Safety experts are lambasting General Motors over what they say is the automaker’s slow notification of owners of certain 2019 sedans and trucks that a recall fix could cause power braking to fail and increase the risk of a crash, the Detroit Free Press reports.  GMÂ’s original recall in December targeted about 550,000 Cadillac CT6 sedans and Chevrolet Silverado 1500 and GMC Sierra 1500 pickups, all from the 2019 model year, over potentially defective electronic stability control and antilock brakes. In that case, GM said the errors would not show up as a diagnostic warning on the instrument cluster. But after GM had done recall work on 162,000 vehicles, about 1,700 owner have complained that their power brakes didnÂ’t work after they had the recall done and then used the OnStar app to start their vehicle. GM then issued a supplemental fix for customers whoÂ’d already had their vehicles serviced. In this case, a diagnostic warning should illuminate saying either “Service Brake Assist” or “Service ECS,” which GM says is a signal that a customer should not drive the vehicle and instead call their dealer, which will tow the vehicle and have it repaired. Safety advocates say the automaker hasnÂ’t gone far enough to protect customers. “The fact that you could potentially start a vehicle and not have brakes is a pretty risky proposition,” Sean Kane, president of the Safety Research and Strategies, which works on auto issues for plaintiffs and governmental organizations, told the Freep. “The fact that they wouldnÂ’t notify owners (sooner) is pretty stunning.” GM told the Freep it was required to notify the National Highway Traffic Safety Administration and file paperwork before it notified customers about the original recall, which was made Dec. 12. It then had to investigate and resolve the problem created by its original recall fix before alerting customers. GMÂ’s call center and dealers are contacting the remaining 900 customers who havenÂ’t yet had the update made to the original recall repair. GM also hired a vendor to send recall letters to the 550,000 customers affected by the original recall notifying them about the update. There are no known injuries or deaths related to the problem. Read the Freep story here.

GM to trim Russian output, raise prices amid currency woes

General Motors is shutting down its factory in Russia's second largest city, St. Petersburg, from the middle of March until the middle of May as the country's currency, the ruble, continues to give economists fits. The ruble's value has plunged due not only to western sanctions, but a precipitous fall in oil prices. We knew these factors were already impacting the auto industry there, as Ford reported in its 2014 earnings statement, and now they're forcing GM to cut production at the factory, shown above, that is responsible for production of the Chevrolet Cruze and Opel Astra. Meanwhile, Automotive News is citing Russian outlet Kommersant as saying that GM has hiked its prices in the country by an average of 20 percent over the past two months. While a GM spokesman confirmed the St. Petersburg plant would be shut down for the two-month span reported by Kommersant and AN, he would not confirm the price increase. News Source: Automotive News - sub. req.Image Credit: Alexander Nikolayev / AFP / Getty Images Earnings/Financials Plants/Manufacturing Chevrolet GM Opel opel astra