2011 Chevy Aveo 5- Only 10k Miles on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Weekly Recap: BMW rolls out ambitious plug-in hybrid electric plan

"We believe that for the United States, this is going to be very important." – Julian Arguelles Let there be no doubt, BMW is serious about electric vehicles. The German automaker said this week it will make plug-in hybrid versions of all of its core models, an aggressive move that demonstrates its commitment to electric propulsion systems. BMW did not specify which vehicles will get the plug-in systems or provide a timeline for when they will arrive. But the announcement is clearly more than blustering, and the company revealed a 3 Series plug-in prototype this week at an event in France. BMW said the 3 Series uses a version of its 2.0-liter turbocharged four-cylinder engine (240 horsepower, 300 pound feet of torque) with an electric motor sandwiched between the engine and transmission in place of the torque converter. It has an all-electric range of 22 miles. A plug-in X5 with the same powertrain was also displayed alongside the 3 Series, though the X5 has been on the auto-show circuit for more than a year, including a recent stop in Los Angeles. Those two vehicles use "eDrive," and BMW's plans represent the first widespread transfer of its technology from development of the i3 and i8 models to more mainstream products. BMW said it's developing electric powertrains so they can be deployed rapidly across its range, and they are flexible enough to be used with fuel cells in future products. Enticingly, BMW is also working on a "Power eDrive" system, which debuted in a 5 Series GT concept at the event in France. This setup has two electric motors powered by a 20-kilowatt-hour battery pack, and when teamed with a four-cylinder turbo, pump out about 670 hp. Reinforcing BMW's commitment, the company will add more than 200 jobs at its factory in Dingolfing, Germany, to support electric-vehicle development. The moves come as BMW and other automakers diversify their portfolios while fuel economy and emissions regulations are getting tighter around the world. The United States has set a 54.5-mpg CAFE requirement for the 2025 model year. BMW said the electric vehicles were developed with an eye toward the US market, its government policies and its wide-ranging commuting styles. "We believe that for the United States, this is going to be very important," spokesman Julian Arguelles said. Ben Scott, a senior analyst in London with automotive research firm IHS, said BMW's moves are expensive – but necessary – to keep pace with the market.

GM CEO to meet with U.S. lawmakers over job cuts

WASHINGTON — General Motors Co Chief Executive Mary Barra plans to visit Capitol Hill next week to discuss the company's plans to halt production at five plants in North America next year and cut up to 15,000 jobs, two congressional aides said on Friday. GM has come under harsh criticism from lawmakers from both major political parties, and from President Donald Trump, since Monday when it announced the biggest restructuring for the U.S. No. 1 carmaker since its bankruptcy a decade ago. Barra is expected to meet with lawmakers from Michigan and Ohio, where GM plans to shutter three plants, as well as senior leaders in Congress. GM did not immediately comment. Barra has been calling lawmakers this week to explain the decision to end production. Trump has threatened to revoke subsidies for GM. The Detroit automaker plans to halt production next year at three assembly plants: the Lordstown small-car factory near Youngstown, Ohio; the Detroit-Hamtramck complex in Detroit; and the Oshawa, Ontario, assembly complex near Toronto. It will also stop building several models now assembled at those plants, including the Chevrolet Cruze, the Chevrolet Volt hybrid, the Cadillac CT6 and the Buick LaCrosse. Additionally, GM plans to shutter the Warren transmission plant outside Detroit and a plant that makes electric motors and drivetrains outside Baltimore, Maryland. The Cruze compact car will be discontinued in the U.S. market in 2019, although GM may continue building it in Mexico for other markets, Barra said. Reporting by David Shepardson. Related Video: