2003 Chevrolet Avalanche 1500 4x4 4wd 4 Door 5.3l V8 Gas Cloth All Power Options on 2040-cars

Auto blog

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

Can DARPA hack into a Chevy Impala through OnStar?

An ex-video game wizard named Dan Kaufman tracked a circuitous route to becoming the head of the Software Innovation Division at the Defense Advanced Research Projects Agency. DARPA normally makes these pages because of its work with autonomous vehicles and automobile technology that overlaps with military applications, but for the past five years Kaufman and his multiple research teams have been working on creating unhackable software code that could be used in military drones. Part of that work has involved hacking into just about everything else, and as a segment on 60 Minutes reveals, that includes cars. The masterminds discovered a way to hack into OnStar, the General Motors telematics system. After figuring out how to hook into OnStar's emergency communication system, they overwhelmed it with data. While the computer was busy trying to manage the overrun of data, the research team inserted code that took control of the sedan's other computers, giving it control. So while reporter Leslie Stahl tooled around in a parking lot, a DARPA researcher with a laptop would occasionally take control of the car, like by applying its brakes or, conversely, removing the ability for Stahl to use the brakes. Hacking into vehicles has been in the news for years: Car and Driver ran a feature on the various ways cars could be hacked in 2011, two hackers released a car-hacking code at the hacker-fest Defcon in 2013 and demonstrated how it worked on a Toyota Prius and Ford Escape, and German researchers demonstrated how they could hack into BMW's Connected Drive remote-services system last week via an attack on the cars' telematics units. This isn't about GM or Onstar or the future; hacking into cars of all kinds isn't coming, it's here, and it doesn't take the half-billion-dollar annual budget of a small DARPA division to do it. Check out the 60 Minutes video on the CBS site (you can watch the entire video from a mobile device without logging in). The OnStar hacking starts at 6:45, but it's worth watching what leads up to that. News Source: Jalopnik Chevrolet Safety Technology Infotainment Autonomous Vehicles Videos Sedan hacking 60 minutes

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck