2005 Cadillac Escalade Pearl White Lthr Loaded Hwy Miles Clean $499 Ship on 2040-cars

Auto blog

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video:

GM recalling 2013 Buick LaCrosse, Cadillac SRX over transmission software

The National Highway Traffic Safety Administration has issued recalls for the 2013 Buick LaCrosse and 2013 Cadillac SRX due to a problem with the software for the transmission controller. On about 27,000 SRX and LaCrosse models, the transmission could accidentally be shifted to Sport mode, which would reduce the amount of engine braking drivers experience.
NHTSA says this could increase the risk of a crash, but, fortunately, the required fix is simply an update to the software.
While we're on the subject of General Motors vehicle recalls, a small number (48) of compressed natural gas versions of the 2011 Chevrolet Express are also being recalled for a potential risk of fire or explosion. Yikes. Both official recall notices are posted below.

Cadillac adds torque-number badging to most new models starting in 2020

Few phrases describe huge swaths of America better than a phrase spotted on the back of a top-fuel dragster at an NHRA event: "You can never have too much horsepower or ammunition." If Cadillac CEO and wily Canuck Steve Carlisle has his way, the revised phrase would substitute "torque measured in Newton-meters" for "horsepower." Starting with the 2020 model year, America's luxury brand will add torque figure badges to CT and XT models, beginning with the XT6. The badge above kinda almost sorta represents the torque produced by the luxury crossover's 3.6-liter V6. That badge did not appear on the XT6 we photographed at the Detroit Auto Show. In U.S. parlance, twist in the XT6 comes to 271 pound-feet. Translated to Newton-meters, that's 367 Nm. Then round that up to the nearest 50, which Cadillac will do, and one arrives at 400. True, the rounding prevents a future of number jumbles like the 2020 XT6 367 vs. the 2021 XT6 419T. Nevertheless, we don't know why Cadillac is rounding to the nearest 50 instead of the nearest 25, since 50 Nm is about 37 lb-ft and could conceal a decent torque increase between model years. A "T" denotes turbocharging, and we imagine there'll be designations for hybrids and electric cars. We think most modern attempts at engine-based nomenclatures soon get as complicated as ciphers or come unmoored from their original scheme. And based on our experience with The Average Car Buyer, they don't care. A bigger number, no matter what that number represents, means more, which is the important thing. Because America, right? Maybe not. Carlisle said, "We're not talking about displacements any more," and the new badging will give consumers "a clear understanding of the power differences across the lineup." The brand believes torque provides a better comparison between ICE, hybrid, and EV powertrains and "the balance between fuel economy and performance." As for the immigrant unit of measurement, Carlisle told CNET, " It's metric, it's universal, it's global, we have to think about all the markets that we're doing business in." Oh, and, "Engineers certainly prefer Newton-meters." The new nomenclature will not be applied to V-series models or the Escalade, because the CEO holds that "special cars get special names." We should probably take a moment to reassure the CT and XT models that Steve Carlisle thinks you're all special, too. Just a different kind of special.