2006 Cadillac Dts Woodtrim Sat. Radio Onstar Remote Start Aux Jack on 2040-cars

Auto blog

Cadillac is returning to endurance racing with a new prototype in 2017

In two months, Cadillac will return to top-tier endurance racing with its all-new Daytona Prototype International racecar after 14 years away. The car, which adheres to IMSA's new DPi regulations, looks as long, low, and Cadillac-like as anyone could have hoped. It's set to debut at the Rolex 24 at Daytona and will compete head to head with the likes of Mazda and Nissan in what is shaping up to be one of the most diverse and exciting forms of American motor racing in years. The new car will be run by Wayne Taylor Racing, the team that previously fielded the Corvette Daytona Prototype. Wayne Taylor himself has won the 24 Hours of Daytona twice, in 1996 and 2005. He now manages the team and leaves the driving duties to his two sons, Ricky and Jordan. They'll be joined in the cockpit by Max Angelelli, Wayne Taylor's teammate in 2002 at Cadillac's last unsuccessful attempt at endurance racing. To understand Cadillac's new car, officially called the DPi-V.R., you need to understand IMSA's DPi category. Basically, manufacturers are allowed to base their car on one of four chassis that follow the FIA LMP2 regulations. The chassis come from either Dallara, Onroak Automotive, ORECA or Riley/Multimatic. Cadillac will base their car on the Dallara platform. The DPi regulation differ from the LMP2 in two major ways: non-standardized engines and the ability to change certain parts of the bodywork. The DPi regulations are intended to give the variety of the top-tier LMP1 cars at a fraction of the cost. When it came to choosing an engine, Cadillac wanted to power the new car with something kinda sorta production based. The new car will use a naturally aspirated 6.2-liter pushrod V8 that shares some base architecture with the engine in the current CTS-V. While the power output hasn't been announced, expect about 600 horsepower. While that's down compared to the CTS-V, there is far less mass to move around as the Dallara chassis is a svelte 2,050 lbs. Since all the teams will be running different engine configurations, expect restrictors of some sort to help balance the power disparity. The parts of the body work that can be modified - The nose, sidepods, rear wheel arches and rear valance - have all been designed to mimic Cadillac roadcar design elements. Even the wheels look like they were pulled straight from the CTS-V. The front splitter, the floor, and the diffuser are common elements shared with other DPi cars.

Petrolicious eats up Rita Hayworth's 1953 Cadillac Ghia

The automotive industry has seem some wonderful transoceanic collaborations between America and Italy, from the Ford-powered De Tomasos of the 1960s to the alliance between Fiat and Chrysler today. Of course it's also seen unfortunate experiments in between like the Chrysler TC by Maserati and the Pininfarina-bodied Cadillac Allante. But before any of those, there was a beautiful tradition of rebodying American steel at the hands of Italian carrozzerie. And this could easily be among the most gorgeous of them all. It's a Cadillac Series 62 from 1953 with bodywork by Ghia. It's one of only two made, and has a star-studded history. The car was purchased by Aly Khan, prince of the Nizari Ismaili muslims and Pakistan's ambassador to the United Nations, for his wife... who just so happened to be the inimitable Rita Hayworth. They split up, but she held on to the car. Today it's part of the permanent collection at the Petersen Automotive Museum in LA, so the videographical artisans at Petrolicious went by to check it out. You'll want to as well in the five-minute short above.

Man trapped in Cadillac XLR for 14 hours after battery dies

A 75-year old Cleveland man ended up trapped in his 2006 Cadillac XLR for 14 hours last month, according to a story reported by the Detroit Free Press. The owner of the car, Peter Pyros, hopped into his roadster to back out onto his driveway, but he quickly learned that the battery was dead. He was "trapped" because the doors use an electric button to activate the door latch to open the door. Since the battery was dead, the buttons did nothing. Now, GM planned for an eventuality like this by placing a manual door release handle on the ground next to the seat. It's marked with a red diagram of the driver-side door opening. There's also a section about it in the owner's manual. The only problem here, was that Pyros says he didn't know the release was there, and he didn't have his owner's manual in the car. Because of this, Pyros may not have made it out alive if not for a neighbor coming to his rescue. "I came to the conclusion that I was going to die ... I was at peace with it. I asked God to help me twice, then I said, 'OK, God if this is the way I'm supposed to die, I will die,'" Pyros said to reporters. There's every chance he could have died in the car, too. Temperatures in Cleveland hit 77 degrees the day he was in the car, and he said it was unbearably hot and difficult to breathe after only 30 minutes sealed inside. Pyros reportedly tried yelling, pounding on and even trying to break the car's windows without success. At one point, Pyros wrote a note to his nephew explaining what happened if he ended up dying. What eventually saved him was a curious neighbor who came to investigate after he noticed his garage door was still open late at night. His neighbor called the police after he found him in the car, and emergency personnel actually ended up charging his car's battery up enough to get the electric door release to work. Of course, after everything settled down, there are now lawyers involved. They're going after GM, with an argument accusing the automaker of not making the emergency latch more obvious both in the car and in the owner's manual. GM doesn't appear to be having any of it. Here's its statement on the matter: "Because this varies by make and model, drivers should review the door lock section of their owner's manual, and follow up with their dealer or customer assistance center if they have any questions," GM spokesman Tom Wilkinson wrote to the Free Press. This type of door release isn't particularly uncommon for GM vehicles.