1998 Cadillac Deville Deville Automatic 4-door Sedan on 2040-cars

Auto blog

Cadillac adds torque-number badging to most new models starting in 2020

Few phrases describe huge swaths of America better than a phrase spotted on the back of a top-fuel dragster at an NHRA event: "You can never have too much horsepower or ammunition." If Cadillac CEO and wily Canuck Steve Carlisle has his way, the revised phrase would substitute "torque measured in Newton-meters" for "horsepower." Starting with the 2020 model year, America's luxury brand will add torque figure badges to CT and XT models, beginning with the XT6. The badge above kinda almost sorta represents the torque produced by the luxury crossover's 3.6-liter V6. That badge did not appear on the XT6 we photographed at the Detroit Auto Show. In U.S. parlance, twist in the XT6 comes to 271 pound-feet. Translated to Newton-meters, that's 367 Nm. Then round that up to the nearest 50, which Cadillac will do, and one arrives at 400. True, the rounding prevents a future of number jumbles like the 2020 XT6 367 vs. the 2021 XT6 419T. Nevertheless, we don't know why Cadillac is rounding to the nearest 50 instead of the nearest 25, since 50 Nm is about 37 lb-ft and could conceal a decent torque increase between model years. A "T" denotes turbocharging, and we imagine there'll be designations for hybrids and electric cars. We think most modern attempts at engine-based nomenclatures soon get as complicated as ciphers or come unmoored from their original scheme. And based on our experience with The Average Car Buyer, they don't care. A bigger number, no matter what that number represents, means more, which is the important thing. Because America, right? Maybe not. Carlisle said, "We're not talking about displacements any more," and the new badging will give consumers "a clear understanding of the power differences across the lineup." The brand believes torque provides a better comparison between ICE, hybrid, and EV powertrains and "the balance between fuel economy and performance." As for the immigrant unit of measurement, Carlisle told CNET, " It's metric, it's universal, it's global, we have to think about all the markets that we're doing business in." Oh, and, "Engineers certainly prefer Newton-meters." The new nomenclature will not be applied to V-series models or the Escalade, because the CEO holds that "special cars get special names." We should probably take a moment to reassure the CT and XT models that Steve Carlisle thinks you're all special, too. Just a different kind of special.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

Cadillac HQ has a New York address

The new home of Cadillac will be in the 330 Hudson building in New York City's Hudson Square, putting the luxury marque smack dab in the middle of three of the city's hippest areas, SoHo, Greenwich Village and Tribeca.
The announcement is yet another milestone in the company's controversial decision to relocate administrative and marketing operations away from Detroit and into the Big Apple.
"The addition of a headquarters office in New York is a key step in Cadillac's ongoing global expansion," Cadillac boss Johan de Nysschen said, according to The Detroit Free Press. "There is no better atmosphere in which to better immerse ourselves into luxury consumer and brand expertise."