1963 Cadillac Coupe Deville Convertible on 2040-cars

Auto blog

2015 Cadillac ATS, CTS recalled over brake issue

A problem with the brakes on the 2015 ATS and CTS has prompted Cadillac to issue a recall. According to the notice below from the National Highway Traffic Safety Administration, the issue revolves around the bracket that connects the brake pedal assembly and the rod that actuates the brakes. Even under normal operation, that bracket could fracture, impeding the ability to slow or stop the vehicle. That, as you're surely aware, could increase the risk of a crash. The issue affects a reported 2,163 vehicles in the United States. Owners will need to be bring their vehicles in to their local dealership to have those brackets replaced starting on August 1. See the complete recall notice below. RECALL Subject : Brake Pedal Bracket may Fracture Report Receipt Date: JUN 09, 2015 NHTSA Campaign Number: 15V358000 Component(s): SERVICE BRAKES, HYDRAULIC Potential Number of Units Affected: 2,163 Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2015 Cadillac ATS and CTS vehicles. The affected vehicles have a bracket between the brake pedal assembly and the rod that actuates the brakes that may fracture during normal brake pedal operation. CONSEQUENCE: If the bracket fractures, the driver would not be able to apply the brakes, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will inspect the vehicle and replace any affected bracket, free of charge. The recall is expected to begin August 1, 2015. Owners may contact Cadillac customer service at 1-800-458-8006. GM's number for this recall is 15352. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

Cadillac's semi-autonomous Super Cruise pushed back to 2017

It looks like General Motors is discovering just how difficult it is to bring autonomous vehicle technology fit for public consumption to market. The company has pushed back the launch of its semi-autonomous Super Cruise technology by several months. Originally promised by CEO Mary Barra for a fall 2016 debut, Super Cruise was supposed to be offered first on the new CT6 sedan. Automotive News is reporting that won't be the case, following a statement from GM confirming that the new system would be pushed to sometime in 2017. At the very least, that's a several month delay. GM cited the need to get the system right and keep owners safe, which prevented a firm date for Super Cruise's debut. Product boss Mark Reuss was more blunt, though, telling AN, "It will come out when it is ready." Super Cruise would be one of the earliest examples of driverless tech to be put into public hands, following the introduction of Tesla's semi-autonomous AutoPilot system in 2015. Most other automakers experimenting with the autonomous vehicles don't foresee public sales until early in the next decade, including Toyota, Renault-Nissan, and Volvo. Before Barra suggested a 2016 debut, GM originally aimed to introduce its semi-autonomous system in 2020. Related Video: