05 Bmw X5 3.0-77k-premium Pkg-pano Roof-auto Trans-self Dimming Mirror on 2040-cars

Auto blog

BMW 1 Series prototype packs direct water injection

Just a few months ago, BMW showcased an M4 that was modified to serve as the safety car for the MotoGP racing series. The flashing lights and emergency equipment, however, weren't the only modifications BMW made to the performance coupe. It also packed an innovative new water injection system. And now it's furthering the development of that system by running it in a 1 Series hatchback as well. Revealed at the BMW Group Innovation Days 2015 event, this five-door 1 Series packs a three-cylinder gasoline engine – like the one found in a Mini or i8 – but fitted with the direct water injection system. In this application, the system sprays a fine mist of water – yep, regular old H2O – right into the combustion chamber. While mixing water with gasoline normally wouldn't be recommended, in this case it evaporates immediately and helps cool the engine from the inside, allowing it to run at higher efficiency. That cooler running engine brings with it several benefits. It delivers improved fuel economy and lower emissions, to start. It also allows for an earlier ignition point, higher compression ratio, and higher boost pressure in turbocharged engines, delivering increased output. It even cuts down on engine knocking (where combustion occurs spontaneously), reduces wear and tear on the engine, and makes better use of lower octane levels. If that sounds like a win-win-win... win (we're losing count of all the wins here), it's because BMW just may be on to something. Of course it does require a water tank to be fitted on board, which means added weight, but instead of requiring the driver fill up the water tank, BMW has fitted this prototype with a system that replenishes the water level from the air conditioning system when the vehicle is switched off. So unless it's being driven in a particularly extreme climate, it doesn't even need topping up. Add one more "win" to the list, then. Extra power, improved real-world fuel economy: Direct water injection enhances efficiency. With direct water injection for turbocharged petrol engines, the BMW Group has again succeeded in enhancing the capabilities of conventional engine technology through an ongoing process of refinement and improvement. The precisely controlled injection of water into the engine cylinders produces a cooling effect that boosts power and torque, particularly when operating at or near full throttle, while at the same time reducing fuel consumption and emissions.

Hamann BMW M6 Mirror can now cash the checks its body writes

Anyone remember the Hamann Mirror? Need a refresher? The Mirror is German tuning company Hamann's idea of a BMW M6. It was shown at the 2013 Frankfurt Motor Show as an M6 Gran Coupe, sporting a ridiculous paint job and some meaty, multi-spoke 21-inch wheels.
Consider this car the Mirror Mark 2. Based on the M6 Coupe, Hamann has applied a similar visual theme, using the same 21-inch wheels from 2013. Whereas the Gran Coupe rode around with a stock powertrain, though, there's been no such restraint with the two-door Mirror. A fine 620 horsepower is available from the 4.4-liter, biturbocharged V8, an increase of 60 horsepower. Torque is up as well, from 501 pound-feet to a whopping 560, meaning this M6 has speed to match its looks. Hamann claims the Mirror's newfound grunt allows it to hit 62 miles per hour faster than the standard M6 (we'd certainly hope so), although it won't mention a specific number.
The suspension, meanwhile, has been dropped 1.37 inches, or about a third of an inch lower than the Frankfurt Mirror. That drop is complemented by the Mirror's bodywork, including the exposed, carbon fiber hood and the flared fenders, which can now accommodate the enormous 305/25 rear rubber. Hamann has also paid some attention to the front and rear aerodynamics.

BMW to offer carbon fiber wheels in a year or two

The Citroën SM sat on the first set of production glass fiber and resin wheels in 1972 when parent company Michelin developed the exotic hoops in order to take the SM rallying. It wasn't until 2008 that we got the first all-carbon-fiber wheel for passenger cars in the form of a prototype model from Weds Sports in Japan that remained a prototype. Australian company Carbon Revolution followed that a year later with its CR-9 all-CF wheel, first introduced on the Shelby Ultimate Aero and now available for independent purchase for about $15,000 per set. BMW could be the first OEM to offer entire wheels in carbon fiber reinforced plastic in two years.
The wheels - either all-CFRP or using a CFRP rim and alloy spokes - were shown off during BMW's Innovation Days in Munich and are products of the development work done on its i-branded cars. The full-CFRP wheel is 35-percent lighter than a forged alloy wheel, the hybrid alloy and CFRP wheel is 25-percent lighter, making for a decent drop in unsprung rotating weight. As demonstrators during a tech day the wheels aren't yet in the pipeline for production and EU approval, but an article in Auto Express claims that they could be on the market as soon as two years from now.
Other possible parts include a full carbon fiber steering wheel and propeller shaft, the latter of which is coming as a single-piece component on the new M3 and M4. BMW is also talking up its use of secondary carbon fiber - waste material from i3 and i8 production - that can be used for items like IP support structures, seat frames and spare wheels in place of traditional metals like aluminum and magnesium. There's an excerpt of the Innovation Day press release below with more details.