2019 Bmw M2 Competition on 2040-cars

Auto blog

BMW 1 Series prototype packs direct water injection

Just a few months ago, BMW showcased an M4 that was modified to serve as the safety car for the MotoGP racing series. The flashing lights and emergency equipment, however, weren't the only modifications BMW made to the performance coupe. It also packed an innovative new water injection system. And now it's furthering the development of that system by running it in a 1 Series hatchback as well. Revealed at the BMW Group Innovation Days 2015 event, this five-door 1 Series packs a three-cylinder gasoline engine – like the one found in a Mini or i8 – but fitted with the direct water injection system. In this application, the system sprays a fine mist of water – yep, regular old H2O – right into the combustion chamber. While mixing water with gasoline normally wouldn't be recommended, in this case it evaporates immediately and helps cool the engine from the inside, allowing it to run at higher efficiency. That cooler running engine brings with it several benefits. It delivers improved fuel economy and lower emissions, to start. It also allows for an earlier ignition point, higher compression ratio, and higher boost pressure in turbocharged engines, delivering increased output. It even cuts down on engine knocking (where combustion occurs spontaneously), reduces wear and tear on the engine, and makes better use of lower octane levels. If that sounds like a win-win-win... win (we're losing count of all the wins here), it's because BMW just may be on to something. Of course it does require a water tank to be fitted on board, which means added weight, but instead of requiring the driver fill up the water tank, BMW has fitted this prototype with a system that replenishes the water level from the air conditioning system when the vehicle is switched off. So unless it's being driven in a particularly extreme climate, it doesn't even need topping up. Add one more "win" to the list, then. Extra power, improved real-world fuel economy: Direct water injection enhances efficiency. With direct water injection for turbocharged petrol engines, the BMW Group has again succeeded in enhancing the capabilities of conventional engine technology through an ongoing process of refinement and improvement. The precisely controlled injection of water into the engine cylinders produces a cooling effect that boosts power and torque, particularly when operating at or near full throttle, while at the same time reducing fuel consumption and emissions.

Mini Cooper SE Convertible wheels made entirely from recycled aluminum

Mini has revealed an interesting fact about its limited-run Mini Cooper SE Convertible: It's the first production car with wheels made from 100% recycled aluminum. Despite sharing the same look as wheels available on the regular SE hatch, they're actually much more environmentally friendly. The wheels were developed with Swiss wheel manufacturer Ronal. The company sells aftermarket wheels under the Ronal and Speedline brands, and it supplies OEMs. And it's no stranger to more environmentally-friendly wheel production. It supplies wheels for the Audi E-Tron GT that are made using a smelting process that produces oxygen rather than carbon dioxide, and it now has a line of claimed carbon-neutral aftermarket wheels. But back to the Mini's wheels. Using all recycled aluminum has the obvious benefit of not requiring new aluminum to be manufactured. But the benefits are greater than just the raw material use. Mini points out that a major improvement in carbon emissions comes from being able to skip the electrolysis process for new aluminum manufacturing. Pure aluminum is extracted from aluminum oxide (which is in turn taken from the mineral bauxite). To do this large amounts of electricity are passed through molten solutions of aluminum oxide and cryolite (which takes energy to heat) across graphite cathodes and annodes. Not only does this use a lot of electricity that has its own carbon costs, the oxygen that separates from the aluminum bonds to the graphite annodes, yielding more carbon dioxide (which is why the production of those Audi wheels is also interesting). In total, Mini says the recycled wheel production reduces carbon emissions by 75%. More specifically, it estimates about 0.16 kilograms (0.35 pounds) per kilogram (2.2 pounds) of aluminum used. Mini also stresses that this process still maintains all the strength of conventional wheels, just in a greener way. And of course, the wheels themselves are recyclable again. Mini, and BMW more broadly, are looking at ways to upscale the process and to source suitable recyclable products, likely other old wheels from cars no longer on the road. Though neither company said anything about when we'll see fully recycled wheels more widely available. Related Video: MINI Electric Pacesetter inside and out

Driving the BMW M2 Competition, Honda Odyssey and Toyota RAV4 Prime | Autoblog Podcast #651

In this week's Autoblog Podcast, Editor-in-Chief Greg Migliore is joined by West Coast Editor James Riswick. This week, they talk about driving the BMW M2 Competition, Honda Odyssey and Toyota RAV4 Prime. Then they discuss James' experience testing the new Yakima CBX cargo carrier, Autoblog readers' preference for the GMC Hummer EV over the Tesla Cybertruck, and Mercedes-Benz taking a larger stake in Aston Martin. Lastly, they help James' father find a new car in the Spend My Money segment. Autoblog Podcast #651 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Rundown Cars we're driving 2020 BMW M2 Competition 2021 Honda Odyssey 2021 Toyota RAV4 Prime Testing the Yakima CBX Cargo Carrier on the Subaru Outback 75% of Autoblog Twitter follower prefer the GMC Hummer EV over the Tesla Cybertruck Mercedes-Benz to boost stake in Aston Martin to 20%, lend it some tech Spend JamesÂ’ fatherÂ’s money Feedback Email – Podcast@Autoblog.com Review the show on iTunes Related Video: