2009 Audi R8 on 2040-cars

Auto blog

For Audi, Quattro name means something for hydrogen cars, too

Forget Dueling Banjos. Audi is proposing "Dueling Motors" for its Audi A7 Sportback H-Tron Quattro concept vehicle. All in the name of appropriate pickup, of course. The German automaker, which showed off the concept sedan at the Los Angeles Auto Show last month, is pairing a plug-in electric motor with a hydrogen fuel cell powertrain. Each motor powers two wheels, maintaining the Quattro's all-wheel-drive pedigree. The car's 8.8-kWh lithium-ion battery can drive the car as far as 31 miles on battery-power alone. After that, the water-vapor-spewing fuel-cell engine kicks in. Audi executive Ulrich Hackenberg told Automotive News Europe that the unusual set-up is necessary because the hydrogen fuel cell powertrain alone would only power two wheels while providing an insufficient 136 horsepower. Not exactly sport-sedan material, especially for a car that weighs about 4,300 pounds, even if it is a zero-emission ride. Combined, the two engines give the sedan 231 horsepower as well as a combined single-charge/full-tank range of almost 350 miles. What it all means is that the A7 can go from 0 to 60 miles per hour in less than eight seconds and has a top speed of about 112 miles per hour, and can still dash through the snow.

With increased range, Audi R8 E-Tron revving up for production. Maybe

As Tesla Motors proved mightily in 2013, an expensive EV with a long range can sell quite nicely, thank you very much. Perhaps Audi was taking notes, since its all-electric R8 E-Tron's on-again/off-again odyssey appears to be on again, according to UK's Autocar, citing Audi's Urlich Hackenburg. The model is near the approval stage for production, and the key to the green-light is the fact that its single-charge range has been almost doubled to 250 miles. The R8 E-Tron gained kudos in these parts last June by turning in a rather brisk 8:09 time around Germany's Nurburgring track, a record for a production electric vehicle (check out the really quiet video here). Still, plans for the 376-horsepower model, which has two electric motors and was first shown off at the Frankfurt Auto Show in 2009, had been put on the proverbial blocks largely because of a relatively short single-charge range of about 150 miles. Then word came out last spring that Audi would produce maybe 10 units before reports from Australia's Drive late last year indicated that plans for potentially broader production were being resuscitated.

Audi 3D-printed this tiny Type C racer, we want to drive it

See this little guy? No, not the one driving – that's Professor Hubert Waltl, Audi's head of production and Volkswagen's chief toolmaker. The thing he's driving, though, is a 1:2 scale replica of the 1936 Auto Union Type C. And it was 3D-printed entirely in house. Not in one piece, mind you. It's too big for that. But the Audi Toolmaking division employed metal printing technology to fabricate all the parts that went into this replica of one of the most dominant of the Silver Arrow grand prix racers of the pre-war era. It's essentially like the pedal car Audi rolled out nine years ago, or the E-Tron concept it showed us nearly five years ago. Only this one uses more advanced manufacturing techniques. Aside from making us want to drive it like nobody's business, the half-sized vehicle serves to showcase the advancements which Audi and the VW Group are making in manufacturing – particularly in the area of 3D printing. The German automaker presently has the technology to print laser-melted layers of metallic powder – either steel or aluminum – with grains measuring half the diameter of a human hair. The equipment can handle objects as large as 7.9 inches high by 9.5 inches wide – which, as small as this little car looks, is still a bit too large to simply print out in one piece. Audi Toolmaking prints "Auto Union Typ C" - Exact model of the "Silver Arrow" from a 3D printer - Audi Board of Management Member for Production Prof. Dr. Hubert Waltl: "This underscores our pioneering role in toolmaking." From powder to a component: With a 3D printer, Audi Toolmaking has produced a model of the historical Grand Prix sports car "Auto Union Typ C" from the year 1936. The company is now examining further possible applications of metal printers for the production of complex components. At the same time, Audi is creating important synergies with toolmaking in other parts of the Volkswagen Group. "We are pushing forward with new manufacturing technologies at Audi Toolmaking and at the Volkswagen Group," stated Prof. Dr. Hubert Waltl, Audi's Board of Management Member for Production and Head of Toolmaking at the Volkswagen Group. "Together with partners in the area of research, we are constantly exploring the boundaries of new processes. One of our goals is to apply metal printers in series production." The Volkswagen Group has a total of 14 toolmaking units in nine countries. Under the leadership of Prof. Dr.