Premium Plus Rare 6-speed Manual One Owner Heated Seats on 2040-cars

Auto blog

Audi A5 and S5 freshen up for 2017

UPDATE: A previous version of this story mischaracterized the 2017 S5's engine configuration. The article has been updated. Well, here's the new Audi A5 and S5. They look a lot like the old ones, but just a tiny bit better. In other words, the redesigned coupes received the same treatment as their four-door counterparts, the A4 and S4. While the German press materials mention both gas and diesel engines, we expect the A5 to carry on in the US with petrol power only. Like the current A5, a 2.0-liter, turbocharged four-cylinder will serve as the base engine, but will probably get a similar power bump as the A4 – Audi hasn't released official figures yet. The four-door had its base output bumped from 220 horsepower and 258 pound-feet of torque to 252 hp and 273 lb-ft of torque. The S5 is a more interesting proposition than the S4. Where the old S5's 3.0-liter, supercharged V6 produced 333 hp and 325 lb-ft of torque, the new, turbocharged, 3.0-liter six-cylinder pumps out 354 ponies, according to the global press materials. That figure, fans of the old 4.2-liter V8-powered S5 will note, is identical to the original S5 that came out for model-year 2008. Torque figures aren't available yet, but we'd bet on at least a small increase in torque. Still, the increase in power is good for a 4.7-second run to 62 miles per hour, a 0.2-second improvement over the current car's 0-60 time. Audi claims it will offer the A5 with both six-speed manuals and seven-speed dual-clutch transmissions, but we wouldn't be so sure about that stick here in the US. The only available gearbox on the A4 is a seven-speed S-Tronic – coupes are inherently more sporting than sedans, but we aren't sure that's justification for Audi to offer a manual-trans A5 here in the US. Audi only mentions an eight-speed automatic for the S5. So no, the German press materials aren't a good indicator of the US-market A5. What we can rely on, of course, are the official images. The original A5/S5 was a handsome car, but Audi's designers have done a swell job styling the 2017 model. It looks good, and is somehow even more refined than last year's car. Audi's new corporate grille works well on a coupe body, although the powerful creases in the hood might be a little too powerful. The tail is lovely, like a prettier A3. The bodies are better looking, but they're also lighter and more aerodynamic, too. The A5's coefficient of drag is down to a slippery 0.25, while Audi's engineers lipo'd 132 pounds of fat.

Car companies may need to start curbing model proliferation

Looking at the current automotive landscape, especially from German makers, you quickly get the impression that less definitely isn't more. BMW alone offers its 3 Series platform in practically every segment possible, including the regular sedan and 4 Series Gran Coupe, which would seem to be direct competitors. Porsche might be the winner, though, with 20 different variants of the 911 listed for sale on its US website. However, some of this model madness might be reaching an end as companies begin cutting back spending or shifting money to other priorities.
According to Yahoo Finance, the offerings from the German automakers are up 25 percent over the past three years to over 200 models in Europe. The peak is expected to come around 2018 at 230 separate vehicles, according to consulting company PwC.
Amazingly, BMW, which is among the poster children for this model explosion, might be changing its tune. "I'm sure there will be points in the future where we look at certain cars and say, 'Maybe we need to think differently now,'" said head of sales Ian Robertson in an interview, according to Yahoo Finance. The statement certainly sounds shocking coming from a company rumored to have 23 front-wheel-drive vehicles all using a single platform on the way.

Audi 3D-printed this tiny Type C racer, we want to drive it

See this little guy? No, not the one driving – that's Professor Hubert Waltl, Audi's head of production and Volkswagen's chief toolmaker. The thing he's driving, though, is a 1:2 scale replica of the 1936 Auto Union Type C. And it was 3D-printed entirely in house. Not in one piece, mind you. It's too big for that. But the Audi Toolmaking division employed metal printing technology to fabricate all the parts that went into this replica of one of the most dominant of the Silver Arrow grand prix racers of the pre-war era. It's essentially like the pedal car Audi rolled out nine years ago, or the E-Tron concept it showed us nearly five years ago. Only this one uses more advanced manufacturing techniques. Aside from making us want to drive it like nobody's business, the half-sized vehicle serves to showcase the advancements which Audi and the VW Group are making in manufacturing – particularly in the area of 3D printing. The German automaker presently has the technology to print laser-melted layers of metallic powder – either steel or aluminum – with grains measuring half the diameter of a human hair. The equipment can handle objects as large as 7.9 inches high by 9.5 inches wide – which, as small as this little car looks, is still a bit too large to simply print out in one piece. Audi Toolmaking prints "Auto Union Typ C" - Exact model of the "Silver Arrow" from a 3D printer - Audi Board of Management Member for Production Prof. Dr. Hubert Waltl: "This underscores our pioneering role in toolmaking." From powder to a component: With a 3D printer, Audi Toolmaking has produced a model of the historical Grand Prix sports car "Auto Union Typ C" from the year 1936. The company is now examining further possible applications of metal printers for the production of complex components. At the same time, Audi is creating important synergies with toolmaking in other parts of the Volkswagen Group. "We are pushing forward with new manufacturing technologies at Audi Toolmaking and at the Volkswagen Group," stated Prof. Dr. Hubert Waltl, Audi's Board of Management Member for Production and Head of Toolmaking at the Volkswagen Group. "Together with partners in the area of research, we are constantly exploring the boundaries of new processes. One of our goals is to apply metal printers in series production." The Volkswagen Group has a total of 14 toolmaking units in nine countries. Under the leadership of Prof. Dr.