2017 Acura Rdx Technology Package on 2040-cars

Auto blog

1997 Acura SLX gets 350 actual Acura horsepower for Radwood

For the Radwood Orange County, Calif., car show, a show themed around 1980s and 1990s cars, Acura is bringing a variety of its original models including a 1991 NSX and a 1986 Integra. The company is also bringing something obscure, a 1997 Acura SLX, the brand's first SUV, offered from model years 1996 to 1999. In some ways, it's something Acura might not want to highlight, since it's really a rebadged Isuzu Trooper, just as the original Honda Passport was a rebadged Isuzu Rodeo. But this SLX is special; it has real Acura power under the hood. The project was led by Acura engineers and Pikes Peak racing drivers James Robinson, Paul Hubers and Jordan Guitar, and the frame and body restoration as well as the powertrain swap was done entirely in-house at Honda R&D in Ohio, according to Acura rep Andrew Quillin. The team pulled out the original naturally aspirated 3.2-liter V6 that made just 190 horsepower and 188 pound-feet of torque, and dropped in a turbocharged 2.0-liter inline-four from a new Acura RDX. That engine also received a new intake, exhaust, turbo and ECU tune, which brought power up to an estimated 350 horsepower and 340 pound-feet of torque, similar to the Graham Rahal Performance RDX. Not only that, but the old-school four-wheel-drive system and live rear axle were dropped in favor of the RDX's indpendent suspension and torque vectoring "Super Handling All-Wheel Drive." "Dropped in" is a mischaracterization, though, as Acura had to weld new subframes front and rear to the existing frame to get the transverse engine and modern suspension to fit. Acura was careful to keep the SLX looking as close to the original as possible. On the outside, Acura repainted the SLX in a modern red paint available on the RDX, but retained the champagne lower moldings. The stock wheels were replaced with 17-inch Fifteen52 wheels, but they have a very similar design and finish to the original wheels. A hard-shell spare tire cover was added, and a simple "SH-AWD" badge on the back is the only hint at what's under the body. The interior was restored at the company's L.A. design studio, where the upholstery was redone in a gray "gathered" leather like you would have seen when it was new. A bit of gray wood trim updates the interior slightly. The RDX's push-button starter and shifter buttons have been added to the center console, shift paddles behind the original steering wheel, and an aftermarket instrument cluster mounted to the steering column.

Acura NSX production delayed

Listeners of the Autoblog Podcast will be familiar with my opinions on the Acura NSX. While I love the idea of Acura building a halo car again, I've routinely joked on-air that the car will never, ever reach production and will continue being teased and previewed ad nauseam. So I'm chuckling at this news: the NSX is being delayed again. To be fair, while it sounds like a big deal – pushing the NSX back from model year 2016 to 2017 – this is a fairly minor delay in the grand scheme. Instead of starting production this fall, as previously announced, the new supercar will start rolling down the line at Honda's Marysville, OH factory in the spring. "Trial production" has already started, Honda says, while briefly acknowledging the delay in the attached press release. While Honda offered no reason for the delay in volume production, Automobile claims it's the fault of the move to fit two turbochargers to the V6, which was made midway through development. Fitting the two iron lungs meant rearranging the six-pot into a longitudinal layout. Here's hoping there are no further delays. Scroll on for a look at Honda's press release, which does its best to gloss over the NSX delay while talking about the company's new Performance Manufacturing Center in Marysville. Related Video: Performance Manufacturing Center: Precision Craftsmanship Aug 14, 2015 - CARMEL-BY-THE-SEA, Calif. The next-generation Acura NSX is produced at the new, dedicated Performance Manufacturing Center (PMC) in Marysville, Ohio, using domestic and globally sourced parts. With trial production already underway and production start-up scheduled for spring 2016, this world-class manufacturing facility employs groundbreaking techniques in weld, body construction, body painting, final assembly and quality confirmation to ensure the highest levels of precision and craftsmanship. More details on the unique and innovative manufacturing processes at the PMC will be rolled out over the months leading up to the start of production, but the following highlights of the new facility were shared during the 2015 Monterey Automotive Week: Innovative blend of people and technology: throughout the PMC, NSX production is centered around the skills of approximately 100 experienced engineers and technicians building the NSX to precise levels of quality and craftsmanship.

NSX Concept-GT is the world's hottest way to boil water

The Honda NSX Concept-GT is one sexy machine, and it looks to be a very effective tool on a race circuit. But Honda's latest web spot leads us to believe that it also can be used to make tea.
In the video, the racecar is hooked up to an apparatus that uses tubing to harness the energy from the car's 500-horsepower hybrid drive system, using it to boil water. The novel tea-making technique reminds us a bit of a couple other inventive Honda commercials, namely Hands and Cog.
Watch the NSX ad below, and be sure to turn the sound up to hear that glorious engine note.