1966 Ford Galaxie 500 Xl on 2040-cars
Henderson, Nevada, United States
1966 Ford Galaxie 500 XL new distributor,starter,power steering pump,plugs,wires,starter solenoid,carb rebuild,ignition wiring harness,oil change. rare model with 390 cubic inch engine 2 door automatic with factory air ac not connected. bucket seats interior is 7 out of 10 no rips in seats power driver seat.Runs strong It's a most see if you love classics if you have any questions feel free to call 702 461 5499 ask for Kevin. $6500 OBO give me a call !! Shipping is to be arranged by purchaser. |
Ford Galaxie for Sale
- 1968 ford galaxie xl fastback - southern car - no rust - rebuilt 302 - match #s
- 1966 ford galaxie 500 hardtop coupe 289 cu in auto 49k texas direct auto(US $13,980.00)
- 1963 ford galaxie 2 door(US $7,200.00)
- 1962 ford galaxie 500xl convertible black w/ red deluxe , 390 v8 4v, ps, pb, a/c(US $23,995.00)
- 1964 ford galaxie 500 convertible (baby blue) runs & looks great. no reserve 302(US $12,000.00)
- 1963 ford galaxie base 4.3l(US $6,000.00)
Auto Services in Nevada
Vinny`s Automotive ★★★★★
Upholstery Works ★★★★★
Tire Xpress ★★★★★
Tire Works Total Car Care ★★★★★
Tahoe City Chevron Center ★★★★★
Sterling Auto Sales ★★★★★
Auto blog
NHTSA upgrades Ford floor mat unintended acceleration probe
Mon, 17 Dec 2012According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"
Ford, GM to collaborate on 9- and 10-speed transmissions
Mon, 15 Apr 2013Back in October, there were reports that General Motors and Ford Motor Company were hard at work co-developing new nine- and ten-speed automatic transmissions, and now both automakers have confirmed this joint operation. While there are no specific vehicles mentioned to receive either transmission, a collaborative press release issued by GM and Ford mention that the transmission will be designed for front- and rear-wheel-drive cars, crossovers, trucks and SUVs.
These aren't the first powertrain components developed jointly between these cross-town rivals, either. The six-speed automatic currently used in vehicles like the Ford Edge, Ford Fusion, Chevrolet Cruze and Chevrolet Equinox was engineered in a similar fashion. As is the case with this existing transmission, both automakers will assist in the design, development and testing of the new transmissions, but each will build its own units in its own factories. Scroll down for the official press release.
Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day
Thu, 13 Feb 2014Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.