1962 Ford Falcon 2-door Hardtop~blue~6 Cylinder~3-speed Manual~no Reserve on 2040-cars

Auto blog

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

2014 Ford Fiesta 1.0L EcoBoost

I'll be honest; when Ford first unveiled its 3.5-liter EcoBoost V6, I was skeptical. Past attempts at building turbocharged American cars were almost universally awful, I reasoned, so why would Ford's latest effort be any different? This may seem foolish today, considering the success that the growing EcoBoost range has achieved - particularly the 2.0-liter and 1.6-liter mills. Yet I once again found myself questioning Ford.
It's the makeup of the 1.0-liter, turbocharged three-cylinder slotted into the compact engine bay of this Fiesta that has a way of breeding doubt. Three-cylinder engines remain an extreme rarity in the US. What's more, they earned a less-than-desirable reputation for applications in the 1980s and 1990s, and my trepidation about this latest three-pot as a result.
As I found out, though, history is a poor informant of modern technology. The thrust available in other cars with the EcoBoost badge on the back has not gone missing here; something the International Engine of the Year committee has lauded. That august body named the 1.0-liter Ecoboost the best engine of 2012 and 2013. After a week of driving, it didn't take long for my fear of threes to get turned into something like that line of thinking.

Ford to add more than 2,000 jobs in Kansas City

Continued high demand for the Ford F-150, along with the addition of the all-new Transit series of commercial vehicles, has led Ford to announce that it will add over 2,000 jobs at its Kansas City Assembly Plant. At the time of the announcement, the plant boasts 2,450 hourly employees working on two shifts. All told, Ford will invest $1.1 billion in the Kansas City plant to expand truck production and begin producing the Transit series.
According to the automaker, fullsize truck sales are up 19 percent through April of 2013, leading to an additional 900 workers and a third shift of production for the F-150. Production of the Transit series will begin in the fourth quarter of this year, requiring an additional 1,100 workers. In addition, Ford estimates that a total of 18,000 jobs will be created by suppliers to its Kansas City plant to support the additional vehicle production.
Want to know more? Scroll down for the complete press release.