Van Wheelchair Handicap 2002 Ford E 250 Low Miles Side Entry Ricon Power Ramp on 2040-cars
Neptune, New Jersey, United States
Body Type:Wagon
Vehicle Title:Clear
Engine:8
Fuel Type:Gasoline
For Sale By:Dealer
Used
Year: 2002
Make: Ford
Model: E-Series Van
Trim: 5.4
Options: Leather Seats
Safety Features: Anti-Lock Brakes, Passenger Airbag, Side Airbags
Drive Type: RWD
Power Options: Air Conditioning
Mileage: 109,000
Sub Model: WHEELCHAIR VAN FORD E 250 BRAUN LIFT
Exterior Color: Blue
Disability Equipped: Yes
Interior Color: Gray
Warranty: Unspecified
Number of Cylinders: 8
This is a very clean 2002 ford e 250 Van with 109000 original miles. The vehicle history report is clean. This Van is equipped with the power RICON Millennium Wheelchair Lift, which operates perfectly. It also has front and rear air conditioning, and the high top for extra headroom clearance. There is capacity for three wheel chairs (including the tie downs) and six additional rear occupants with foldaway seats. There has been only one owner since new, which was a private health care company. All vehicles from this company have a bumper-to-bumper service contract until the day they are sold. As a result, this vehicle was fully serviced every 3000 miles, and got the best service and care at every maintenance interval regardless of cost. This Van runs and drives beautifully. The 5.4L engine runs strong and smoothly, and the transmission shifts perfectly. The suspension and steering feel nice and tight. The tires are all showing most of their tread, and the brake pads are in good condition as well. The oil & filter and the air filter were freshly changed, and there aren’t any service indicators or warnings lights on. The white finish is glossy and in great condition over the entire body. This Van is a clean looking Van. Both of the bumpers are in great shape. All of the doors open smoothly and easily. The interior of this Van is clean and in great condition as well. All interior trim pieces are intact, tight and in very good condition. This was a non-smoker operated vehicle, and there aren’t any smoke odors or burn marks inside this Van. We have the clean, clear title without any liens or encumbrances. This is a very clean Van that runs perfectly, and is ready to be picked up and put into use immediately. PS, PB, PW, PM, PL, PM, Tilt, Cruise, Ice-Cold Front and Rear A/C Runs, and Drives Perfect, Everything Works Great Super Clean Inside, and Out, Excellent Paint, Excellent Interior. Winning bidder must contact us within 24 hours of
auction end, and make arrangements for payment at that time. A $500.00 non-refundable
deposit is due within 24 hours of end of auction. The remainder is due within 7
days of auction end. If no contact is made within 24 hours we reserve the right
to re-list the vehicle, sell it to the next high bidder, or sell it otherwise.
We have been a licensed Automobile Dealership in New Jersey. We are primarily an Auto Wholesale Operation supplying other dealerships, and we are now listing select vehicles for sale to the public as well. I am the internet/wholesale manager and my name is Jean. Please feel free to call me with any questions at 732 895 3081.
|
Ford E-Series Van for Sale
- 1992 ford e-150 econoline mark iii conversion package low miles
- 2009 ford econoline cargo van e150 high security great condition(US $10,997.00)
- Handicap van(US $18,000.00)
- 1999 ford e350 ambulance 7.3l powerstroke diesel
- Ford : 2012 e250 hightop wheelchair paratransit conversion 31k mi warranty
- Ext cargo van - 1-ton - 6.0 turbo diesel - new tires - storage shelves - 1-owner(US $18,998.00)
Auto Services in New Jersey
Yellow Bird Auto Diagnostic ★★★★★
White Horse Auto Pke ★★★★★
Vulcan Motor Club ★★★★★
Ultimate Drive Auto Repair ★★★★★
Sparx Auto ★★★★★
Same Old Brand ★★★★★
Auto blog
US Ford Focus RS to be imported from Europe
Tue, 21 Oct 2014Rumors about the forthcoming Ford Focus RS are flourishing into what sounds like a very impressive new hot hatch. The latest scuttlebutt gives the first indication about when we might see a few of these fast Focuses on roads here in the US.
Unnamed insiders reportedly confirmed to The Truth About Cars that Ford plans to launch the Focus RS in the US in 2016. However, getting one might not be so easy - the boosted powertrain means the car would likely need to be imported from Europe. That's likely going to keep the total number available in the US rather low. The sources estimate a price tag that's a bit more expensive than the top Focus ST3, which starts around $28,500, plus $825 destination.
It seems that a pretty potent package comes for all of that cash, though. The Focus RS reportedly uses a 2.3-liter turbocharged four-cylinder making between 325 and 350 horsepower, with a torque-vectoring all-wheel drive system to get that muscle to the road. The test mules also wear more aggressive front and rear fascias, dual exhaust tips, larger brakes and sticky tires. It sounds like a great formula on top of the already enjoyable Focus ST.
The history and future of the Ford Bronco
Tue, 17 Jun 2014
Some have suggested that the Bronco's demise was hastened by the fallout from the O.J. trial.
Twenty years ago today, ex-NFL linebacker Al "A.C." Cowlings drove his friend and onetime running back Orenthal James "O.J." Simpson on a parade lap of the Los Angeles highway system and onto an ignoble page of the history books. If you're in your late 20s or older, or a fastidious young student of 1990s American history, you're absolutely aware that Al and O.J.'s steed for the 'chase' was a white Ford Bronco. The white Ford Bronco, even.
Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day
Thu, 13 Feb 2014Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.
2040Cars.com © 2012-2024. All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.
Use of this Web site constitutes acceptance of the 2040Cars User Agreement and Privacy Policy.
0.031 s, 7226 u