2004 Dodge Durango Slt Sport Utility 4-door 5.7l on 2040-cars

Auto blog

NHTSA investigating Ram 1500 models for rear differential failure

The National Highway Traffic Safety Administration is investigating Fiat Chrysler Automobiles and its Ram brand following a number of reports regarding the 2005 Dodge Ram 1500 pickup. According to 15 consumer complaints, the trucks' rear differential locked up while in other cases, the driveshaft separated at its connection to the diff.
Nearly half of the reports claim the truck was traveling at or above 50 miles per hour, while two consumers reported that the diff lockup/driveshaft separation sent their pickups into a spin. Most troubling, though, is that consumers reported little to no sound indicating there was a problem with their truck.
We reached out to Ram for additional information, such as how many vehicles may be affected or what equipment might be fitted that could cause the issue. Unfortunately, the company wasn't willing to elaborate on specifics.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

2015 Dodge Challenger SRT Hellcat [w/videos]

Darrell Waltrip once said, "If the lion didn't bite the tamer every once in a while, it wouldn't be exciting." The sentiment behind that aphorism is causing my adrenal gland to wake up as Dodge and SRT drivers and engineers - somber-faced to a man - give me the track talk that will precede my driving the 2015 Dodge Challenger SRT on the circuit at Portland International Raceway. PIR might not be Daytona, and the 707-horsepower Challenger Hellcat might seem tame to a legend like ol' Jaws, but there's a not-small part of me that's thinking about how hard Dodge's fire-breathing kitty might bite.
Just a few hours previous, I'd gotten behind the wheel of the Hellcat for the first time, letting its hyperbole-spitting, supercharged V8 Hemi pull me yieldingly through Portland's morning commuter traffic. Lulled into a cocky certainty by the Challenger's good manners at low speed, I drove the throttle just a hair too deep, too fast when I ran on to the highway ramp. For just an instant the rear tires were utterly drenched in torque, and the back end of the big Dodge loosened up like a drift car on a wet track. Throttle steer lives at the fleeting whim of your right foot in this car.
It was no big thing to lay off the gas and pull the Hellcat back in line as I entered the highway, but the incident did get me to thinking: What will this car do to me on a road course?