1969 Dodge Dart Gts 2-door 5.6l 340 Clone... on 2040-cars

Auto blog

2014 Dodge Durango leaks ahead of NY rollout

Even though Chrysler will reportedly discontinue the Dodge Durango after the current model's lifespan - said to be around 2016 - that isn't stopping the automaker from improving its full-size, three-row SUV. The vehicle won't debut at the New York Auto Show until tomorrow, but images are already leaking out ahead of the embargo lift, and they show that the 2014 model is getting even more aggressive styling to go with more technology inside and out.
Dodge limited its early press shots of the new Durango to just the R/T trim level, but this new look adds a meaner look to this model with more dramatic projector-beam headlights along with a "floating" crosshair grille and a restyled fascia. At the rear of the Durango, LED racetrack taillights show a family resemblance to the Charger and Dart, while a new rear fascia adds to the styling while also allowing for an integrated trailer hitch.
On the tech side, the instrument panel looks to have been redesigned to include a standard seven-inch thin-film transistor (TFT) gauge cluster, and it also appears as if Chrysler's well-liked UConnect system has been updated with the 8.4-inch touchscreen found in other Chrysler vehicles. The 2013 model's conventional console shifter has been replaced by a rotary knob for gear selection, suggesting that there are transmission changes afoot as well. We'll have more details when the silks slide off this big boy tomorrow, so stay tuned.

Chrysler extends fuel tank warranties on LX cars, NHTSA ends probe

The National Highway Traffic Safety Administration has ended its investigation of 153,817, 5.7-liter and 6.1-liter Hemi V8-powered 2006 Chrysler 300, Dodge Charger and Dodge Magnum models after reports of stalling. Chrysler has responded by granting a lifetime warranty on the fuel tanks for these vehicles.
NHTSA received 299 reports of engines stalling while the models were stopped or driving at low speeds, and began an investigation. The government agency found that the control valve shutoff float in the V8s' 19-gallon fuel tank could malfunction if the fuel had too high of an ethanol content. In many cases, the valve would break in the open position, allowing the tank to be overfilled, which would then cause the cars to stall. However, there were no accidents reported, and the vehicles could be restarted immediately.
There will not be a recall on these vehicles because, "the condition represents a low risk to motor vehicle safety and is adequately addressed by Chrysler's extended warranty," NHTSA said to The Detroit News.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.