1968 Dodge Coronet Rt Hemi 4 Speed 1 Of 100 Built 426 Dana 60 354 Og Interior on 2040-cars

Auto blog

2014 Dodge Journey Crossroad

Watchers of the auto industry will notice a theme among the formerly bankrupted American automakers, General Motors and Chrysler. There are the post-bankruptcy vehicles, and the pre-bankruptcy vehicles. The former, in the case of Chrysler, include the Jeep Grand Cherokee, as well as the 200 and 300. For GM, there's the Cadillac ATS, Chevrolet Impala and Buick Encore, among others. These vehicles have the freshest styling, with sharp exteriors and well-crafted interiors, as well as advanced powertrains and well-sorted chassis.
As for the pre-bankruptcy vehicles, they tend to be easy to spot. Most suffer from inferior driving dynamics, cheaper interiors, poorer fuel economy and often homely looks (we know, there were some decent cars before the bankruptcy, but they were pretty heavily outweighed by the bad ones). Think late, last-generation Chevrolet Impala or Chrysler 200. Increasingly, though, we're seeing vehicles that split the balance between pre- and post-bankruptcy. Vehicles like the Dodge Journey.
The Journey debuted in 2007 as a 2008 model year vehicle, meaning it should fall into the latter category. But heavily breathed upon in 2011, it now enjoys a new, 3.6-liter Pentastar V6, a big, critically acclaimed touchscreen display and in the case of today's tester, a new-for-2014 Crossroad spec.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.