2007 Chevrolet Uplander Base Mini Cargo Van 4-door 3.9l on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.