Chevrolet Nova on 2040-cars
Tuckerton, New Jersey, United States
1963 Chevrolet Nova. No post. Front sub frame. 327 with mild cam, Edelbrock, Holley, Headers, Etc. 4 speed, 4.10 rear, Slide a link traction bars. Billet Specialties rims. Nice interior with console. Nice exterior. Car is done right! Has not been hacked up! Pick up with cash only!
|
Chevrolet Nova for Sale
- 1972 chevrolet nova base coupe 2-door 6.6l
- 1967 chevy ii nova vintage chevrolet runs drives hot rod rat rod drag car clean
- 1970 chevy nova ss 454 4-speed big block loaded (like-new) custom
- 1972 nova, magazine featured car, full hotchkis suspension, black / black
- 1965 chevrolet nova ss nice cruiser check it out!
- 1966 chevy ii nova tci front end
Auto Services in New Jersey
Xclusive Auto Tunez ★★★★★
Volkswagen Manhattan ★★★★★
Vito`s Towing Inc ★★★★★
Vito`s Towing Inc ★★★★★
Singh Auto World ★★★★★
Reese`s Garage ★★★★★
Auto blog
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.
Watch this creative way to pull a truck's engine
Fri, 08 Mar 2013Living in an apartment complex has its benefits, but for shade-tree mechanics who like/need to work on their own cars, it definitely has a number of disadvantages. Relatively simple tasks such as brake jobs and oil changes are difficult when you don't have dedicated driveway space, to say nothing of more in-depth repairs... like pulling an engine, for example.
For these types of challenges, a little ingenuity and plenty of muscle are needed to get the job done. Scroll down to watch these four men snatch the V8 out of a Chevrolet K1500 using nothing but a chain, landscape timber and good ol' fashioned brute strength. Good work, gentlemen.
Camaro spy shots show subtly different grille, front fascia
Sun, 03 Feb 2013It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.