1994 Corv. Conv 6 Spd. W/ Cc2 Top - Polo Grn / Tan - 38000 Mi - Immac In / Out on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

GM profits threatened by glut of pickups

Automotive News reports that General Motors may slash production or ramp up discounts in order to deal with an oversupply of pickup trucks. GM currently has more than double the standard supply of pickups, and the vehicles are threatening to dampen the automaker's profits for 2013. Typically, automakers try to sustain a 60- to 75-day supply of vehicles, but GM is currently loaded with a 139-day supply, as of last month. At the end of November, the automaker was sitting on 245,853 units.
The manufacturer says that it will adjust production accordingly before laying any incentives on the profitable pickups. Even so, there's some concern that the inventory swell could hurt the roll-out of the next-generation Chevrolet Silverado and GMC Sierra. GM actually began slowly stepping back production in August, but it's clear the company will take further action as it heads toward the end of the year and into the next. Analysts predict the automaker could reduce pickup manufacturing by nearly half in the first quarter of 2013.
That still may not be enough to keep GM from laying extra cash on the Silverado and GMC Sierra. While the company's incentive spending was down in November compared to the same month in 2011, both the Ram 1500 and Ford F-150 saw double-digit percentage increases in sales last month while the Silverado and Sierra numbers slid compared to a year prior. Incentive spending could help move more trucks and add some balance to the GM inventory surge.