2008 Platinum Cadillac Srx Base Trim on 2040-cars

Auto blog

2013 Cadillac XTS [w/video]

The Cadillac Of Stopgaps
As confusing as most alphanumeric car names have gotten in recent years, at least one constant has been that the letter "X" is generally indicative of a crossover. Then why did General Motors use this letter on its new 2013 Cadillac XTS luxury sedan? Well, for that, we'll have to look to the world of mathematics where "X" stands for an unknown variable or a placeholder. Now we're talking. The XTS is just an interim product sitting at the top of Cadillac's four-door food chain until the brand gets a true flagship in place. That sounds like a lot of resources to spend on what will likely be a one-and-done model, but the automaker needed to get something - anything - to replace the DTS.
So here you have the 2013 XTS. A big luxury sedan that was created to bridge the gap between Cadillac's recent past and its pending future. Going into our week with this XTS knowing that it was a stopgap measure proved to be both a blessing and a curse. On one hand, we know (or hope) that this car will act as a baseline for future high-end Cadillac models, but at the same time, we couldn't help but be mindful of past stopgap models, albeit in more entry-level segments, like the Cimarron and Catera.

Cadillac SRX production moving to TN, next-gen Equinox going to Mexico

It's a good week for the town of Spring Hill, TN, as General Motors has announced that its factory in the city of 31,000 will receive a $185 million contract to produce engines. On top of that, the next-generation Cadillac SRX crossover will be built at the factory (NA models are presently built in Ramos, Arizpe Mexico), which was once famous for being the home of GM's now-defunct Saturn brand.
The factory is one of GM's six facilities around the globe that will screw together the company's new line of three- and four-cylinder Ecotec engines. Spring Hill currently builds the 2.0-liter, turbocharged Ecotec, as well as the naturally aspirated 2.4 and 2.5-liter variants.
Spring Hill's vehicle assembly lines were idled in 2009, but were reactivated in 2011. The SRX is just one of the products meant to benefit from last year's $350-million investment, and should have a positive impact, creating or retaining around 1,800 positions at the factory.

Autoweek divulges details on Presidential limo

Ever since the latest presidential limousine, also known as The Beast, debuted in 2009, we've wondered what's underneath that black Cadillac body. We already know a few details, like the fact it isn't a Cadillac at all, but a very heavy duty truck chassis from General Motors with a body that resembles a super-sized Caddy. Autoweek, however, has managed to extract new details from veteran Secret Service agents about the closely guarded presidential limo. Their methods, of course, are classified.
Designed to be a rolling office, bunker and escape pod all in one, the current presidential limo is far different from previous presidential state cars, which were heavily modified production vehicles. As we would expect, The Beast uses thick, military-grade body armor (eight inches on the doors), an armored fuel tank, special run-flat tires with Kevlar lining, an encrypted satellite phone, a fully sealed cabin with its own oxygen supply and a trunk full of weapons and medical equipment that includes a supply of the President's blood type (in case the car gets cut off from the ambulance that's always present in the President's motorcade).
The Beast also comes with a Halon fire-suppression system, night vision and is powered by a V8 engine, which we already knew runs on gas and not diesel, that returns an EPA-unfriendly estimated 3.7 miles per gallon. The Secret Service operates a fleet of 12 limos and each Beast costs $1.5 million. Lastly, AW estimates that the 18-foot-long state car weighs 15,000 pounds, and each Secret Service agent that drives the car must be specially trained to maneuver such a massive vehicle.